Originally Posted by _DX3_ (Post 134697)

Well I finally got to mow the yard with the 1711 this weekend. It mowed great. I finished up and went in to get a drink and hook up the yard sweeper and start doing that. Sat down to start the engine and it just turned, without wanting to start. I pulled the plugs and could smell that I was getting fuel. Checked for spark, and saw absolutely nothing. I got out the KT17 service manual and figured I would check the coil. Was supposed to get 4 to 5 ohms resistance with meter set at Rx1k and the probes touching the + and - posts. I got 3. Then I checked secondary resistance at the high tension lead posts. With the meter set to Rx100k I should have seen, 9,500 to 11,500 ohms resistance. The needle pegged zero. Oh well, new coil and plug wires ordered, will be here in the morning. Just to have it on and know it is new, I'll get a new fuel pump next and that should have most everything new and updated. I did purchase new points and condenser, but when I pulled the cover the points were brand new and the timing was set perfectly. The condenser checked out good also, as it too was new.

Originally Posted by jbrewer (Post 134701)

Duke , that's not going to buff out....:biggrin2:

Was the lecture about "....I told you two this was going to happen....." painful to endure?

;-)
John

Originally Posted by _DX3_ (Post 134703)

LOL, dang Duke, you all play rough. :biggrin2:

Originally Posted by Methos (Post 134695)

Evan nad I was having another go at racing around the yard yesterday and we had a slip up! Mom and little sis came out side to play on the play set and I hollered at Evan to slow down and he hit the brakes on the 1864 in the turn and I couldn't get the 1650 stopped in time.:bigeyes: The 1650's front right tire hit the left rear on the 1864. I didn't even hear it break but saw the tire under the foot rest.:blush: I used a chain and the cat0 on the 1864 to take it to the garage. I've got an axle from Chip aka cub149 several months ago that I'm going to put in it. Super steer upgrade!:beer2:

I know how much Sam loves his pics!

Originally Posted by Methos (Post 134695)

Evan nad I was having another go at racing around the yard yesterday and we had a slip up! Mom and little sis came out side to play on the play set and I hollered at Evan to slow down and he hit the brakes on the 1864 in the turn and I couldn't get the 1650 stopped in time.:bigeyes: The 1650's front right tire hit the left rear on the 1864. I didn't even hear it break but saw the tire under the foot rest.:blush: I used a chain and the cat0 on the 1864 to take it to the garage. I've got an axle from Chip aka cub149 several months ago that I'm going to put in it. Super steer upgrade!:beer2:

I know how much Sam loves his pics!

Originally Posted by CADplans (Post 134711)

We need a close-up showing where the pulley notched the axle!!

(Got to find some way to blame this on the PO!!)

Originally Posted by ACecil (Post 134715)

Glad you and Evan are ok, buddy!

Originally Posted by Sam Mac (Post 134717)

Seriously? Pics from you? Must be a full moon. LOL

Like they say "Rubbin’s Racin" :biggrin2:

Originally Posted by _DX3_ (Post 134858)

The new coil worked great. The 1711 fired right up this morning with no issues, even sounds a lot smoother. I'll have to get with Todd and get that fuel pump number. I need to get it changed. :beerchug:

Originally Posted by _DX3_ (Post 134858)

The new coil worked great. The 1711 fired right up this morning with no issues, even sounds a lot smoother. I'll have to get with Todd and get that fuel pump number. I need to get it changed. :beerchug:

Originally Posted by inboardnut (Post 135002)

Hope you dont mind, (I had also posted a few pics in the implement section).
I tried out my "new" Befco tiller! A few bugs to work out, but, Wow!!!

BTW, the little Kubota loves it as well!

Originally Posted by inboardnut (Post 135002)

Hope you dont mind, (I had also posted a few pics in the implement section).
I tried out my "new" Befco tiller! A few bugs to work out, but, Wow!!!

BTW, the little Kubota loves it as well!

Originally Posted by _DX3_ (Post 135082)

Tillers look so good behind Supers. Love the action pics. Allen, I can't wait for you to get yours. I want to see lots of pics. :beerchug:

Originally Posted by ACecil (Post 135093)

I hear ya, DWayne! You'll definitely see some pics. :biggrin2::beerchug:

Originally Posted by jbrewer (Post 135160)

There's something unnatural about not seeing a 100 in your avatar, Allen :bigthink:

John

Originally Posted by Methos (Post 135053)

Awesome pics and impressive set up! You need to submit those for POTW!

Originally Posted by jbrewer (Post 135160)

There's something unnatural about not seeing a 100 in your avatar, Allen :bigthink:

John

Originally Posted by inboardnut (Post 135172)

what/where/how?

Originally Posted by Sam Mac (Post 135151)

Duke I'll get you some pics tomorrow of this AWESOME MOWSHENE. :beerchug:

Originally Posted by Sam Mac (Post 135254)

Duke

Pics of the 129 as promissed. Gave the old girl a bath and tuned on it a bit. Runs like a real one now. Glad I didn't part it out. It should make someone a nice tractor.:biggrin2:

Originally Posted by _DX3_ (Post 135322)

Got to mow again with the 1711. New Coil made a huge difference. I have come to the conclusion I hate turf tires with only air in them. This thing spins the rear tires so easy...:bash2: Guess I'll have to add ags and fluid to the Christmas and Birthday list this year. :biggrin2: I am going to have to take the starter out and see if I can clean it. It stuck on me twice today. Not really a big deal, I have a long screwdriver I can use to get the bendix gear back into place, but it is just a PITA to have to do it. I am keeping my fingers crossed it is a starter with a nut on the end of the gear instead of one of those newer style permanent fixtures.

Originally Posted by CADplans (Post 135326)

See my thread on poofing my starter!!

http://www.onlycubcadets.net/forum/s...ad.php?t=18071

It might help!! :bigthink: