Only Cub Cadets - 3 Point Lower Lift Arm Dimn?

Page 2 of 2

Show 40 post(s) from this thread on one page

Only Cub Cadets (https://www.onlycubcadets.net/forum/index.php)

- Implements and Attachments (https://www.onlycubcadets.net/forum/forumdisplay.php?f=16)

- - 3 Point Lower Lift Arm Dimn? (https://www.onlycubcadets.net/forum/showthread.php?t=42004)

J-Mech

12-16-2015 01:57 PM

There are 2 different arms. One for a SGT and one for a GT. Not narrow and wide frames.

1811woody

12-18-2015 01:31 PM

Quote:

Originally Posted by J-Mech (Post 355272)

Woody, what are you talking about???? :bigthink: Wide and narrow frames using different arm? The frame is the same width at the rear no matter what machine.... and they didn't install Cat 0 hitches on narrow frames. That didn't come about until the 982. It was the first CC with a Cat 0. Are we talking about the same things?? :Huh:

CC-03-200 look this up on extreme motor works this is the info I was basing my info from

J-Mech

12-18-2015 04:05 PM

Quote:

Originally Posted by 1811woody (Post 355521)

CC-03-200 look this up on extreme motor works this is the info I was basing my info from

Yes. That is a hitch than Aaron at xtreme designed and built for the narrow frames. That is not a reproduction of a Cub Cadet hitch. It is custom made.

It says that in the description: "New Category 0 - 3 Point lift system. Complete kit. Never produced before!!!"

1811woody

12-18-2015 04:42 PM

Yep like I said "special"

J-Mech

12-18-2015 08:09 PM

But you understand don't you that the narrow frame custom made 3ph uses the same arms as the factory produced GT hitch right? There are still only 2 different arms offered by xtreme. The GT and SGT.

PeterJ

12-20-2015 05:53 PM

Quote:

Originally Posted by 1811woody (Post 355098)

I would like to be able to convert my sleeve hitch to a 3 point of sorts so if I come across a implement that is a 3 point that I cant live without I'm able to use it. The dimension to the outside of the sleeve hitch is 14.25. According to the info I've read a cat 0 is 20 inches so I'm looking at the cc-03-006 lift arms does anybody have a set they can measure and tell me what the offset is of these arms so I know if it is enough offset to give me the needed 20"

I just brought the 1863 with the 3-point home. If you want me to take some measurements pm me your number and I'll call you.

PeterJ

1811woody

12-20-2015 07:47 PM

Thank you for the offer, I may do that next weekend. I saw your post on your 1863 congrats.

red56turbo

12-20-2015 09:08 PM

Woody,
Do you live in the Quadcities? If so, you're welcome to run up to my place and take some measurements/pics. I've got a 3 point on my 782D and another laying on the shelf due to go on the 1512. I live outside of DeWitt. PM me if you're interested and I can get you directions and my cell number. :beerchug:

1811woody

12-20-2015 10:40 PM

That's great! I will do that perhaps next weekend I will pm you. Thank you.

red56turbo

12-21-2015 07:33 PM

No problem. Just give me a holler via PM if interested.

All times are GMT -4. The time now is 06:06 PM.

Page 2 of 2

Show 40 post(s) from this thread on one page