Only Cub Cadets

Only Cub Cadets (https://www.onlycubcadets.net/forum/index.php)
-   CCC/MTD Cub Cadet built Tractors (GT) (https://www.onlycubcadets.net/forum/forumdisplay.php?f=10)
-   -   Bought my first smoker CCC 882 (https://www.onlycubcadets.net/forum/showthread.php?t=41805)

bsb369 11-26-2015 08:54 PM

Bought my first smoker CCC 882
 
Just bought my very first diesel cub today an 882. It's in fair shape missing the side panels but runs great and the 44 inch mowing deck is quite as a mouse only 1142 hrs. I did notice that it had a few leaks under the rear end. I don't know a lot about this model anything I should check for or any known problems inherent with this model??.

PeterJ 11-26-2015 11:35 PM

Congrats on that find! I had a 1512 (same model just newer - 1986?) for 20 years. I just sold it this summer to someone that approached me to buy it. When I bought it in 1995, the hour meter had been replaced and it had new rear tires. I think its first 8 years of service was full time commercial duty. It had LOTS of hours on it. I put about 600 hours on it. You will love the Kubota.

I replaced the hydro relief valve on mine, back in the '90s, because it was leaking fluid all over the rear end. That worked for a very short while and it started leaking again. I just kept a piece of cardboard under it from then on. Maybe the power or vibration of the Kubota has something to do with the leaking? I don't know.

It starts MUCH better if over 40 degrees - I fought it for 4 years and then put heat in the shop and everything was fine after that. Make sure the cables are good and your have a strong battery. Interstate makes a good one that will fit in the small space.

About five years ago I started having fuel issues. It would run for about 5 minutes of snowblowing and would run out of power. Shut it off for a few minutes and it would run again for about 5 minutes. It ended up being "floaties" in the fuel tank.

Just follow good maintenance practices and if it is in good shape that 30 something year old garden tractor will still last for GENERATIONS. If you run into a problem just ask here if you need help.

PeterJ

zippy1 11-26-2015 11:40 PM

Congrats on the tractor:beerchug:
I would check the bolts that attach the diff to the frame and make sure they are not loose or possible broke. It (your leak) could be axle tube or rear cover gaskets also. You'll just have to clean everything and see what you find.
But the first thing would be the diff attachment locations...:bigthink:
Good luck, the experts should be along shortly with other opinions.

Rescue11 11-27-2015 01:36 AM

Congratz! looks like you have some good advice already!

bsb369 11-27-2015 06:14 AM

I really appreciate the advice I pulled the center cover off that's between the seat and the dash and sure enough it does look like it is leaking around the relief valves next I will check the differential bolts on the frame and in the rear cover. Once again, I really appreciate your advice you guys are great on here

Terry C 11-27-2015 08:15 AM

Congrats on your 882!

bsb369 11-27-2015 08:18 AM

Just curious will any 82 series sleeve hitch work on this machine??

J-Mech 11-27-2015 08:47 AM

Any off of a hydro model.

Mcamp 11-27-2015 09:51 AM

You have the alum. rear end,to use a sleeve hitch you will need a different lower bracket and check for clearance on your fuel tank for the top mount.

Oak 11-27-2015 09:52 AM

Quote:

Originally Posted by bsb369 (Post 353312)
Just curious will any 82 series sleeve hitch work on this machine??

bsb369, congrats on a great little tractor.

You will need to find a cat 0 hitch because the fuel tank will be in the way of the top lift lever. Then you will need an A frame adapter to use sleeve hitch equipment.

Pull the fender pad off and give it a good cleaning. Here is a good thread on the valves.http://www.onlycubcadets.net/forum/s...ad.php?t=34139
If you pull the fenders, pull and clean the tank too. Check, clean or replace the tank fittings, replace the fuel lines and filters and you won't have to worry about fuel issues for years.

Check the drive shaft and rag joints for any wear.

Oh ya, we need pics of your new machine too.:biggrin2:

J-Mech 11-27-2015 10:09 AM

Is it the fittings that are in the way? The tank doesn't sit any lower than the battery box on the other machines..... :bigthink:

bsb369 11-27-2015 10:34 AM

1 Attachment(s)
Thank you for all the great advice..... I was looking at the tractor and it does look like the fuel tank is in the way of the top piece of the sleeve hitch..... That's a bummer...,..didn't want to have to put a cat 0 hitch on..., but if that's what it takes. It looks a little rough but runs and mows great I'm going to go look at a parts tractor Sunday that has the side panels.....still not a bad deal at 800 bucks

Oak 11-27-2015 10:49 AM

2 Attachment(s)
That was a smoking deal for sure.

Rich Patton has the panels. He can do the exhaust cutout needed too.

Here is how the tank is on the diesel GT's.
Attachment 70011 Attachment 70012

bsb369 11-27-2015 11:01 AM

My problem is..... I have a 1A tiller..forgive me this may be a stupid question.... But is there anyway I can make it work with this tractor??

J-Mech 11-27-2015 11:07 AM

Still not understanding why the tank is in the way...... Looks like there is room for a sleeve hitch, no issues.

Oak 11-27-2015 07:19 PM

1 Attachment(s)
J, here is a little better pic. I don't see how the top lever would fit. I'll see if I have a close up pic.
Attachment 70038

bsb, I think you can use one of these for your tiller.
http://www.xtrememotorworks.com/Part...20Featured.htm
http://www.ebay.com/itm/Cub-Cadet-Ti...kAAOSwHnFV5I-~


There was a guy up your way that made a nice GT cat 0 hitch for a little over $300 a few years ago. I'll see if I can dig his info up.

CubDieselFan 11-27-2015 10:28 PM

Congratulations on the diesel. You will like it.

bsb369 11-28-2015 08:15 AM

Oak I really appreciate all your help. Looks like that's the way I'm going to have to do it. Let me know if you find that guys number I would be interested in contacting him. Once again thank you

ACecil 11-28-2015 09:52 AM

Congrats on the smoker! :beerchug:


All times are GMT -4. The time now is 04:17 PM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.