|
PLEASE PATRONIZE OUR SPONSORS!
|
|||||||
 |
|
|
Thread Tools | Display Modes |
|
#2
10-27-2013, 06:18 PM
|
|||
|
|||
I think the 1712 shares the same frame size as a 782. You can find a cat 0 hitch for a 782 at
http://www.xtrememotorworks.com/Part...rts%20List.htm Will want to double check with them for fit. Good luck 
|
|
#3
10-27-2013, 06:33 PM
|
|||
|
|||
|
Quote:
Both use the Hydraulic Cylinder that exists on the tractor.
__________________
[B]Roland Bedell[/B] CC Models: 100, 105, 1450, 782, (2) 784, & 2072 [SIZE="4"][B][COLOR="Red"]Buy:[/COLOR][COLOR="Blue"] Made in the USA[/COLOR][/B] [/SIZE]:American Flag 1:
|
|
#5
10-28-2013, 06:01 AM
|
||||
|
||||
|
If you go to Extreme's website you can tell how the Cat 0 hitch attaches to the tractor and how it works. It uses the same ram that the OEM lift uses but allows more movement than the OEM lift and it keeps the same relative angle with the ground as it is lifting rather than swinging an arc like it does on the OEM lift. There is a rear plate that covers up the existing rear end and that is where the mechanical advantage is located. I do not know what the difference in lifting capacity between the two lifts is but I'm sure Extreme can tell you.
__________________
1811 Hydro "Failing to prepare is preparing to fail". 
|
|
#6
10-28-2013, 05:58 PM
|
||||
|
||||
|
I don't think you can tell the difference in operation from a OEM or Exrteme cat 0 lift. I have one of each and can't tell the difference between the two. They use a piece of flat steel for the lift bar that attaches to the front rockshaft with a pin and it runs to the rear rockshaft that is on the rear frame plate. A sleeve hitch is completely different.
Here is what the lift bar looks like. There are 2 in this picture. The slotted end attaches to the rear rockshaft. The slot is to give the attachment some floating ability.
__________________
This ain't no hobby....it's an addiction
|
|
#8
10-29-2013, 10:40 PM
|
||||
|
||||
|
Sorry I can't find any pictures on my puter.
There is a hole on the left side of the bar I have pictured and it has a counter bore so that the head of the pin when installed is flush with the bar. The picture of the tractor has a red arrow of the hole in the frame where the pin goes in at. You will need to pull the tunnel cover off and put a cotter pin through the pin on the drive shaft side of the lift bracket. If I remember correctly you will need a longer pin than the one that is in there now. Here is the link to the cat 0 parts. http://www.partstree.com/parts/?lc=c...&dn=0064700001
__________________
This ain't no hobby....it's an addiction
|
|
#9
10-29-2013, 11:53 PM
|
|||
|
|||
|
OAK Thanks for the pictures and info, the next time you have the tunnel cover off could you take some measurements for me? I am going to make it all my self.
Also is the diesel in the picture yours? Is it just gt or sgt?
|
|
#10
10-30-2013, 08:38 AM
|
||||
|
||||
|
Go to the Xtreme web site, click on cat O 3 points and then down load the install manual. That should give you a good idea of what is involved.
http://www.xtrememotorworks.com/Part...rts%20List.htm
__________________
2264 with 54 GT deck 1641 AKA Black Jack with a 402-E Haban Sickle bar mower JD317 dump truck BX2670 with FEL
|
|
|
|
Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.
MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.
This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC
All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.
Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.
Linear Mode
