|
PLEASE PATRONIZE OUR SPONSORS!
|
|||||||
 |
|
|
Thread Tools | Display Modes |
|
#4
08-03-2015, 05:57 PM
|
||||
|
||||
shouldn't hurt anything, id run it.
__________________
Tim Pap's 100 Restored 108 1211 Dual Stick 1050 Pap's 100 restoration thread - http://onlycubcadets.net/forum/showthread.php?t=47965 
|
|
#5
08-03-2015, 06:26 PM
|
|||
|
|||
|
Agreed.
Get a new bearing or two and run it.
__________________
Randy Cubs: 71, 72, 127, 149, 1440, 2186 and 1864 John Deere 110 round fender John Deere 140 H3 Sears: GTV16
|
|
#6
08-03-2015, 06:33 PM
|
||||
|
||||
|
I'm a new guy here. I know some will laugh, but JB Weld and sandpaper will make that look almost new and last as long as the tractor.
You'll want to file or carefully grind down any high spots first. Put on the JB and let dry. Sand slowly. Check the (new) bearing fit often. When it goes on snugly, your ready to put it together. I fixed truck steer axle that way years ago.
|
|
#8
08-03-2015, 06:54 PM
|
|||
|
|||
|
You can mig weld that spindle a little. Grind the high spots off so the bearings will slide on it and use it.
|
|
#9
08-03-2015, 07:31 PM
|
|||
|
|||
|
You could also try a spindle upgrade like:
http://www.loaderplans.com/spindle-upgrade I did my 1512 years ago. I suspect a good welding shop can remove the spindle and weld up a new shaft for a lot less than the price for new. Could also watch evil bay or try one of the sponsors for a used one. Good luck!
|
|
#10
08-03-2015, 08:10 PM
|
|||
|
|||
|
Someone has already been welding and grinding there.
I would run it also. What's the worst that could happen?
__________________
More IH Cub Cadet Parts RIGHT HERE
|
|
|
|
Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.
MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.
This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC
All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.
Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.
Linear Mode
