Only Cub Cadets

PLEASE PATRONIZE OUR SPONSORS!

CC Specialties R. F. Houtz and Sons Jeff in Pa.

P&K Cub Cadet Machtech Direct

Cub Cadet Parts & Service


If you would like to help maintain this site & enhance it, feel free to donate whatever amount you would like to!




Attention Guest, We have turned off the forum to guest. This is due to bots attacking the site. It is still free to register.

-->
Go Back   Only Cub Cadets > Cub Cadets > Implements and Attachments

Notices

Reply
 
Thread Tools Display Modes
  #1  
Old 04-27-2012, 11:13 AM
machinehead323 machinehead323 is offline
Senior Member
 
Join Date: Apr 2012
Location: Texas
Posts: 194
Default tiller gear box lower pulley info

Can someone give me the diameter of the tiller gearbox lower pulley, also what is the overall height total of the pulley and the diameter of the shaft hole? I am putting it on a #1 tiller, and tring to cross referance a pully from McMaster Carr.
__________________
1979 1650, #1 tiller with one extension, 90 degree box mounted, 3 point. 1961 4 digit bringing back to life. I have the mower and 3 pint for it. The 1650 is the fastest mower in the neighborhood.
Reply With Quote
  #2  
Old 05-07-2012, 02:29 PM
machinehead323 machinehead323 is offline
Senior Member
 
Join Date: Apr 2012
Location: Texas
Posts: 194
Default

anyone have any info on the tiller lower pulley?
__________________
1979 1650, #1 tiller with one extension, 90 degree box mounted, 3 point. 1961 4 digit bringing back to life. I have the mower and 3 pint for it. The 1650 is the fastest mower in the neighborhood.
Reply With Quote
  #3  
Old 05-07-2012, 02:43 PM
ajcombs's Avatar
ajcombs ajcombs is offline
Senior Member
 
Join Date: May 2011
Location: NC
Posts: 727
Default

Measured with a tape measure and eye so until some one posted up actual I wouldnt buy unless it was cheap lol

Mine has a 5inch diameter and looks like 3/4 inch shaft with a key of some kind.

Good luck
__________________
1782 smoker!!, 169 and parts 128
And a bunch of stuff that fits on the back of them LOL
Reply With Quote
  #4  
Old 05-07-2012, 05:16 PM
Matt G.'s Avatar
Matt G. Matt G. is offline
Senior Member
 
Join Date: Mar 2009
Location: Wichita, KS
Posts: 5,661
Default

Measure the width across the two belt notches in the gearbox plate; the OD of the pulley is slightly less than the distance between the outside edges of each notch since the belt has to go though there. You'll need one with a fairly long hub because it hangs down pretty far below the gearbox. I think a 3/4" shaft uses a 3/16" key, but I can't remember, so hopefully someone will provide that measurement.
Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 04:08 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.

Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.

MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.

This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC

All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.

Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.