Only Cub Cadets

PLEASE PATRONIZE OUR SPONSORS!

CC Specialties R. F. Houtz and Sons Jeff in Pa.

P&K Cub Cadet Machtech Direct

Cub Cadet Parts & Service


If you would like to help maintain this site & enhance it, feel free to donate whatever amount you would like to!




Attention Guest, We have turned off the forum to guest. This is due to bots attacking the site. It is still free to register.

-->
Go Back   Only Cub Cadets > Off Topic > General Talk

Notices

Reply
 
Thread Tools Display Modes
  #1  
Old 10-17-2016, 09:19 AM
samckitt samckitt is offline
Senior Member
 
Join Date: Nov 2012
Location: Virginia
Posts: 276
Default Will tins from a 682 work on a 2072?

Assuming the 2082 is one that is referred to a cyclops. Will a normal cub metal fit on one of them, 682 fit on 2082? Assuming I will have to change the pedestal/dash parts too.
__________________
________________________
Scot
Reply With Quote
  #2  
Old 10-17-2016, 10:37 AM
Sam Mac's Avatar
Sam Mac Sam Mac is offline
Administrator
 
Join Date: Feb 2010
Location: Galax VA
Posts: 18,874
Default

Pretty involved conversion. Cyclops have tilt steering, the battery tray is different between the Cyclops and the previous design, hydraulic plumbing and valves are different. Just to name a few. Some have done conversions by modifying the top of the Cyclops dash tower. Guess it depends on how handy you are doing sheet metal work.
__________________
2264 with 54 GT deck
1641 AKA Black Jack with a 402-E Haban Sickle bar mower
JD317 dump truck
BX2670 with FEL
Reply With Quote
  #3  
Old 10-17-2016, 10:39 AM
samckitt samckitt is offline
Senior Member
 
Join Date: Nov 2012
Location: Virginia
Posts: 276
Default

If I have a complete 682 to use, would that make it any easier? I understand it has tilt column that would be an issue.
__________________
________________________
Scot
Reply With Quote
  #4  
Old 10-17-2016, 11:05 AM
Sam Mac's Avatar
Sam Mac Sam Mac is offline
Administrator
 
Join Date: Feb 2010
Location: Galax VA
Posts: 18,874
Default

If the only issue is that you don't have the plastic I would just replace that. You can still get it from Cub new or try the sponsors for used parts.

If your dead set on doing a conversion start looking for something like an 1872 to rob the parts from.
__________________
2264 with 54 GT deck
1641 AKA Black Jack with a 402-E Haban Sickle bar mower
JD317 dump truck
BX2670 with FEL
Reply With Quote
  #5  
Old 01-15-2017, 09:58 AM
samckitt samckitt is offline
Senior Member
 
Join Date: Nov 2012
Location: Virginia
Posts: 276
Default

Is the frame on a 2082 the same as an 1872? I found part number s for both, numbers are different. But are they physically different? Can they be interchanged?
__________________
________________________
Scot
Reply With Quote
  #6  
Old 01-15-2017, 10:38 AM
Sam Mac's Avatar
Sam Mac Sam Mac is offline
Administrator
 
Join Date: Feb 2010
Location: Galax VA
Posts: 18,874
Default

Pretty sure you can swap them.
__________________
2264 with 54 GT deck
1641 AKA Black Jack with a 402-E Haban Sickle bar mower
JD317 dump truck
BX2670 with FEL
Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 06:03 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.

Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.

MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.

This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC

All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.

Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.