PLEASE PATRONIZE OUR SPONSORS!
|
|
Thread Tools | Display Modes |
|
#1
|
|||
|
|||
Camshaft end play
Reassembling a K321 AQS and need to get some shims to set the camshaft end play. Manual calls it out to be .005 - .010. I have .011+, not quite .012. Looking at the McMaster Carr site and was wondering if anyone could verify if these would be proper;
Spring Steel Round Shim, 0.005" Thick, 1/2" ID, 3/4" OD (part # 90482A125) http://www.mcmaster.com/#standard-shims/=13t9pno (Edit: See post #10 below) |
#2
|
|||
|
|||
Well, if they fit then they'll work. Why wouldn't they?
At .002" over I'm not sure I'd worry about it, but then again it may have a cam knock. I doubt it though. |
#3
|
||||
|
||||
Is that measurement with the original shim in it?
__________________
Tim Pap's 100 Restored 108 1211 Dual Stick 1050 Pap's 100 restoration thread - http://onlycubcadets.net/forum/showthread.php?t=47965 |
#4
|
|||
|
|||
|
#5
|
||||
|
||||
Ok, I was just wondering. I'd order the shims and get it a little tighter, hate for you to go through all this work and have a slight knock.
__________________
Tim Pap's 100 Restored 108 1211 Dual Stick 1050 Pap's 100 restoration thread - http://onlycubcadets.net/forum/showthread.php?t=47965 |
#6
|
|||
|
|||
Just wondering if the 3/4" OD spring steel ones that I linked to would be a better choice over the plane carbon steel shims they also sell or should I just stick with the 1" OD Kohler shims.
Quote:
Thanks guys. |
#7
|
|||
|
|||
cub
This is what i'd do too. I/ve been on the upper end and had a slight cam knock. Used balance gear shims can work also. Mike
|
|
|
Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.
MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.
This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC
All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.
Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.