|
PLEASE PATRONIZE OUR SPONSORS!
|
|||||||
 |
|
|
Thread Tools | Display Modes |
|
|
|
#1
07-02-2015, 10:45 PM
|
||||
|
||||
Onan Teardown help
Hey Guys, Before anyone points it out.. yes I have been to the Tractor Forum article on "How to rebuild your Onan engine" Yes it's fantastic and very helpful. However I'm stuck in the teardown process at a spot before the Article starts. If anyone could offer some tips or guidance it would be appreciated. I have the Onan out of the tractor finally! I have all of the shrouding completely off. I removed the rear screen and exposed the flywheel. I was able to remove the bolt that holds the flywheel into the Crankshaft but the flywheel it's self will not budge. I am not sure what to do and I don't want to force anything for fear of breaking something. Am I missing something here? Is there some secret bolt or pin holding it in I am not seeing? Also the front PTO will not come off. I have 2 stripped bolts holding it to the engine block. I'm picking up some stripped bolt removal tools tomorrow. However, I can't get the bolt that holds it to the Crankshaft to break loose. Is this a reverse thread or something? Whats the best way to break this seal so i can get the front PTO off and the flywheel off?
__________________
Javier~ 1980ish 982 w/ 3pt. & PTO /50C deck - a Work in progress. Brinly Moldboard Plow. I'm a complete noob at this so please take it easy on me. 
|
|
#3
07-02-2015, 10:55 PM
|
||||
|
||||
|
Quote:
http://www.amazon.com/636-Distributi...eel+puller+set
__________________
Javier~ 1980ish 982 w/ 3pt. & PTO /50C deck - a Work in progress. Brinly Moldboard Plow. I'm a complete noob at this so please take it easy on me.
|
|
#4
07-02-2015, 10:57 PM
|
||||
|
||||
|
Also I know I will need a gear puller and that it has to be really heavy duty for this. are there any recommendations on a good affordable gear puller that will work for getting that timing gear off?
__________________
Javier~ 1980ish 982 w/ 3pt. & PTO /50C deck - a Work in progress. Brinly Moldboard Plow. I'm a complete noob at this so please take it easy on me.
|
|
#5
07-02-2015, 11:29 PM
|
||||
|
||||
|
You can't get the PTO bolt in the crank to come loose? Are you using an air wrench? Just curious, what do you mean stripped bolt removal tools?
__________________
2072 w/60" Haban 982 with 3 pt and 60" Haban 1811 with ags and 50C 124 w/hydraulic lift 782 w/mounted sprayer 2284 w/54" mowing deck
|
|
#6
07-02-2015, 11:55 PM
|
||||
|
||||
|
Quote:
as for stripped bolt removers. I found these. I'm not sure they will work as the space to get in there is really tight.  http://www.amazon.com/Craftsman-Bolt...d+bolt+remover
__________________
Javier~ 1980ish 982 w/ 3pt. & PTO /50C deck - a Work in progress. Brinly Moldboard Plow. I'm a complete noob at this so please take it easy on me.
|
|
|
|
Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.
MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.
This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC
All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.
Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.
Hybrid Mode
