|
PLEASE PATRONIZE OUR SPONSORS!
|
|||||||
 |
|
|
Thread Tools | Display Modes |
|
#1
10-14-2012, 08:43 PM
|
||||
|
||||
Wheel Weights on 26x12-12's
Before I take the two IH weights (each side) off of my 100 with 8.50's, I was wondering if the dish on a 26x12-12 is any, or much bigger than an 8.50?
 If it is, I will have to pick up some more bolts obviously...but I am just curious as to if I will have to, or not.
__________________
-105___ Tiller 
|
|
#2
10-14-2012, 08:55 PM
|
||||
|
||||
|
I have 65 lb gilson wheel weights that get swapped between my 122 with 8.50's ( tilling )and the 10.50's on my 125 (snow duty ).
The 8.50's have a good inch of thread sticking out while the 10.50's are closer to flush. Good chance the twelves are deeper yet.
|
|
#3
10-14-2012, 10:08 PM
|
||||
|
||||
|
Quote:
Good to know!  Well, then I suppose I could at least put one set on.
__________________
-105___ Tiller
|
|
#4
10-14-2012, 10:29 PM
|
||||
|
||||
|
They will work because both have 12in diameter rims. You might have to get longer bolts though because the supers have a deeper dish. You will probably need 7 or 8in bolts. I just swapped my wheel weights from my 1250 (23-8.5-12) to my 782D (23-10.5-12) and had to go from 5''x1/2'' bolts to 6''x1/2'' bolts.
__________________
Adam Current Workhorses: 1977 1650, Sleeve hitch, #2 tiller; 1985 782, QA 42A snowblower, 50'' deck, 42'' blade, Ags, IH Wheel weights; 197? 1250; 1976 1250, hydraulic lift, 44'' deck, 54'' blade (currently needing a engine) Current Projects: 1970 107, Sleeve hitch, 42'' deck, Tri Ribs, 8'' Brinley Plow Family owns over 30 tractors, 7 combines, 2 bulldozers, 2 mid size trucks, 1 semi, too many truck and scouts to count including parts, and 3 pulling tractors. All vintage IH.
|
|
#5
10-14-2012, 11:20 PM
|
||||
|
||||
|
Quote:
Yeah, I figured it would work...but I was hoping that I could get by with the same bolts.  At least I could put one set on, with the current bolts.
__________________
-105___ Tiller
|
|
#7
10-15-2012, 06:59 AM
|
||||
|
||||
|
Conner while your at it load the tires. The Supers are light in the butt and need all the weight you can get.
__________________
2264 with 54 GT deck 1641 AKA Black Jack with a 402-E Haban Sickle bar mower JD317 dump truck BX2670 with FEL
|
|
#8
10-15-2012, 07:16 AM
|
||||
|
||||
|
I just filled my Turfs with chains this weekend...2 tires in about 20 minutes and they weigh a ton! just break the bead, pour in your favorite anti-freeze, fill to the max with a water hose, and hit it with air...I have about 10psi in them currently but may change once on the Super...As I have weighted Ags on it now...
Easy and cheap....
|
|
#9
10-15-2012, 07:52 PM
|
||||
|
||||
|
Quote:
Show off...  Quote:
Probably will, I suppose. Quote:
That easy? No leaks without tubes? How much solvent per tire?
__________________
-105___ Tiller
|
|
#10
10-16-2012, 08:06 AM
|
||||
|
||||
|
No leaks..
I put in about 3/4 gal of antifreeze and the rest water in each tire....It really doesnt get that cold here so that should work.... Now when I was in Michigan!!! That's another story!
|
|
|
|
Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.
MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.
This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC
All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.
Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.
Linear Mode
