|
PLEASE PATRONIZE OUR SPONSORS!
|
|||||||
|
|
Thread Tools | Display Modes |
|
#1
03-12-2024, 08:11 PM
|
|||
|
|||
K321, Two More Questions.
I fired up the 149 today to do the carb, Hi/Lo rpm, and hydro neutral.
At 1,600 rpm the thing shakes like a Labrador coming out of the water, but at 1,400 its as smooth as a puppies belly so that's where it will stay. Top end is set at 3,200 for now, I seldom run it above 3,000 anyway. I don't mow with it. The questions: The manual for the 149 says three pints of motor oil. That puts me right on the "ADD" mark. It will probably take another two pints to come to the halfway mark. Too much oil is not good in a dipper splash system but too little is not good in anything. I do have the dipper on the rod cap. Does any body know for sure what the capacity is? Question #2. My carb is a Walbro WHG. According to the pics in the manual, my high speed mixture screw should be right on top and the low speed near the block at an angle. I'm guessing my high speed is down low (in the pic) The manual says start at one turn out for the low and two turns out for the high. But since I don't have the same carb they're talking about, I'm not sure. Another manual I found online doesn't even give a start point just "to be determined". Neither screw has much affect over a wide range of adjustment until it gets real lean, then it quickly pops and almost dies. I suspect my throttle plate shaft is loose, so that may be the problem on the idle circuit. Not sure what's going on with the high speed circuit.  Any enlightenment would be appreciated.  EDIT: The site won't let me load the pics from my phone? 
|
|
|
Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.
MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.
This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC
All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.
Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.
Threaded Mode