|
PLEASE PATRONIZE OUR SPONSORS!
|
|||||||
 |
|
|
Thread Tools | Display Modes |
|
#1
12-10-2015, 07:33 PM
|
||||
|
||||
Hydraulic lift weak
My snow thrower isn't lifting high enough, about and inch. I even tried xtreme motorworks adjustable lift Rod and lift bracket extender. If I manually lift the thrower higher, it sags right on down. Is this a problem with the hydraulics?
__________________
1973 Cub Cadet 149 2023 John Deere X590 Farmall B sitting in relative's barn 
|
|
#3
12-10-2015, 07:45 PM
|
||||
|
||||
|
Quote:
__________________
1973 Cub Cadet 149 2023 John Deere X590 Farmall B sitting in relative's barn
|
|
#4
12-10-2015, 07:54 PM
|
|||
|
|||
|
Quote:
If you lift the blower by hand and it leaks down, you either have an issue with the valve, or the cylinder. Check to make sure that the linkage to the spool valve is allowing it to center. You can do this by moving the handle just slightly forward, then slightly back and see if it stops creeping down. If now, then you need to check and see if the cylinder is bypassing internally. Easiest way to do that is to raise the blower up all the way and block it. Then, remove the line on the opposite end of the cylinder (rod end), take the block that is holding the blower up out and see if oil comes out of the fitting. If so, replace the cylinder. Only a few tools required.  Checking the pressure of the operating system is not a bad thing.... but will not tell you if your cylinder is leaking, or if you have a valve issue. Since it won't hold up the blower, my bet is the cylinder needs rebuilt.
|
|
#5
12-10-2015, 08:01 PM
|
||||
|
||||
|
Well it does hold up the thrower as high as it'll lift it. But if I manually lift it higher, it squishes down to same height it had lifted it too. It doesn't leak down to the ground. It's acting like the pressure is bypassing and it can't lift it high enough. It also seems weak in reverse like I can't get to full speed like it used to. That's why I'm suspect of the fluid level. I filled it to the plug height, but didn't recheck it after running the engine and pressurizing the system.
__________________
1973 Cub Cadet 149 2023 John Deere X590 Farmall B sitting in relative's barn
|
|
#6
12-10-2015, 08:13 PM
|
|||
|
|||
|
Post a pic of the rear end cover. Maybe someone changed it out with the one from a gear drive. The fluid level plugs are lower on a gear drive.
There won't be much fluid loss after running the system, and shouldn't really be any measurable amount. Less than a pint. If you started it and it lost more than that, you didn't fill it the first time. It holds 2 gallons, the pump holds less than a pint and the cylinder.... maybe 2 pints. Point is, if you filled it full.... the level wouldn't be too low to give issues. Post some pics of it in the raised position from the RH side. 
|
|
#8
12-10-2015, 09:28 PM
|
||||
|
||||
|
That's the right rear cover.
Take the tunnel cover off and watch it go up and down and see if everything is moving correctly
__________________
Terry O,100,72,102,123,104,124,105 125,129,149,1200,982 (2)2182s w/60in Habans 3225
|
|
#9
12-10-2015, 09:47 PM
|
|||
|
|||
|
Quote:
 Also, you could have a sheared roll pin on the implement lift lever by the foot rest (RH side).
|
|
#10
12-10-2015, 11:09 PM
|
|||
|
|||
|
Could have also sheared the spiral pin through the rock-shaft in the lift arm that the cylinder fastens to.
__________________
More IH Cub Cadet Parts RIGHT HERE
|
|
|
|
Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.
MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.
This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC
All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.
Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.
Linear Mode
