Only Cub Cadets

PLEASE PATRONIZE OUR SPONSORS!

CC Specialties R. F. Houtz and Sons Jeff in Pa.

P&K Cub Cadet Machtech Direct

Cub Cadet Parts & Service


If you would like to help maintain this site & enhance it, feel free to donate whatever amount you would like to!




Attention Everyone, we have 2 new Sponsors!
Machtech Direct and P&K Cub Cadet (See Links above)


Go Back   Only Cub Cadets > Cub Cadets > CCC/MTD Cub Cadet built Tractors (GT)
Reload this Page Confused ...... a Hydro 1872 question
Register FAQ Calendar

Notices

Reply
Page 2 of 2 1 2
 
Thread Tools Display Modes
  #11  
Old 01-05-2019, 07:36 PM
ccpullin ccpullin is offline
Senior Member
  
Join Date: Oct 2009
Location: Iowa
Posts: 166
Default
With it not running, try partially un-screwing the filter to purge the air from the pick up tube, then tighten filter back up once fluid comes out and try it again. If it still wont prime you will have to fill the filter with fluid before installation.
Reply With Quote
  #12  
Old 01-05-2019, 07:51 PM
Gr8lite Gr8lite is offline
Member
  
Join Date: Nov 2018
Location: Maine
Posts: 52
Default
Ill loosen the filter tomorrow when I get back to it. And see what happens.

Pretty tough to fill a horizontal filter ......

Thanks to all! I’ll keep y’all posted.
Reply With Quote
  #13  
Old 01-05-2019, 08:00 PM
ccpullin ccpullin is offline
Senior Member
  
Join Date: Oct 2009
Location: Iowa
Posts: 166
Default
Quote:
Originally Posted by Gr8lite View Post
Ill loosen the filter tomorrow when I get back to it. And see what happens.

Pretty tough to fill a horizontal filter ......

Thanks to all! I’ll keep y’all posted.
I typically fill the filter before installation on everything including my vehicles. On horizontal installations I fill the filter and let the oil soak in to the element. Then I start rotating the filter as I turn it to the horizontal position and screw it on with little loss. If you have to take the filter off to fill it you will loose several quarts so be sure to place a clean oil drain pan under it for re-installation of oil.
Reply With Quote
  #14  
Old 01-05-2019, 10:19 PM
farmall fred's Avatar
farmall fred farmall fred is offline
Senior Member
  
Join Date: Jul 2010
Location: Defiance Ohio
Posts: 390
Default
Try this, raise the front wheels off the ground and start the tractor, then start turning the steering wheel to full left and right. It will allow the air to purge out through the steering valve through the return line. Sometimes when I change the hydraulic filters on some of our older 66 series farm tractors that is the only way to get the pump to prime up. I had this happen once to one of my hydro cubs and it worked for me.
Reply With Quote
  #15  
Old 01-05-2019, 10:58 PM
ol'George's Avatar
ol'George ol'George is offline
Grand Member
  
Join Date: Oct 2009
Location: MI
Posts: 6,679
Default
The filter is on the suction side, unscrewing it will only suck more air into the system.
Wrap a rag around an air hose and introduce a pound or two into the system through the fill hole, thus helping to prime the system with oil under a slight pressure.
Careful as you don't want to use a large amount of pressure, just a couple of pounds.
BTDT works well.
Reply With Quote
  #16  
Old 01-06-2019, 06:17 AM
Oak's Avatar
Oak Oak is offline
Senior Moderator
  
Join Date: Jun 2009
Location: Georgia
Posts: 5,168
Default
I would also check and make sure you didn't do something to the suction tube that is near the drain plug.
__________________
This ain't no hobby....it's an addiction
Reply With Quote
  #17  
Old 01-06-2019, 06:42 AM
ccpullin ccpullin is offline
Senior Member
  
Join Date: Oct 2009
Location: Iowa
Posts: 166
Default
Quote:
Originally Posted by ol'George View Post
The filter is on the suction side, unscrewing it will only suck more air into the system.
Wrap a rag around an air hose and introduce a pound or two into the system through the fill hole, thus helping to prime the system with oil under a slight pressure.
Careful as you don't want to use a large amount of pressure, just a couple of pounds.
BTDT works well.
You don't have it running when you loosen the filter to purge the air from the suction line. The fluid level is above the the filter so it will purge the air out.
Reply With Quote
  #18  
Old 01-06-2019, 12:32 PM
Gr8lite Gr8lite is offline
Member
  
Join Date: Nov 2018
Location: Maine
Posts: 52
Default
Must have needed to purge air out, got to the shop today and all is good , everything works as normal and sounds good!

Thanks to all for your helpful ideas!
Reply With Quote
  #19  
Old 01-07-2019, 07:02 PM
farmall fred's Avatar
farmall fred farmall fred is offline
Senior Member
  
Join Date: Jul 2010
Location: Defiance Ohio
Posts: 390
Default
Glad it worked out for the best for you. Looks like gravity finally did its job and filled the filter. It is always a concern when something like this happens.
Reply With Quote
Reply
Page 2 of 2 1 2

« Previous Thread | Next Thread »

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -4. The time now is 06:35 PM.

www.onlycubcadets.net - Archive - Top

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.

Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.

MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.

This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC

All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.

Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.