PLEASE PATRONIZE OUR SPONSORS!
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
127 pulley welded to shaft
Longtime lurker, recent signup and first post…
I picked up a 1969 127 that had been for sale along a nearby road. It was cheap and there were obvious things missing, but it runs well and drives well with no creeping or leaks. It’s a 55-year-old tractor… Digging in, though, I’ve discovered that a previous owner welded the clutch drive pulley and associated hardware to the output shaft. It appears to have been converted into a yard towing machine rather than a ground working tractor. I had figured on using it to eventually mow the yard. I’m debating now whether to keep going with this as this is beyond the scope of what I can do in my garage. The question is whether I can get someone to break/grind the welds to get the basket pulley off and replace it to reverse whatever it is they did. Or if it’s all welded together permanently. I’m not a metalworker or a machinist, so I don’t know if this looks to be reversible without damaging the crankshaft. I also don’t know what these parts look like disassembled to know the extent of how this is all locked together. The engine appears to be original, so I’d like to keep it together with the chassis. Thoughts/suggestions? |
#2
|
||||
|
||||
You can get someone to grind off the what looks like the locking collar from the PTO bearing if you're uncomfortable doing it yourself. Hopefully both the collar and pulley basket will come off easily.
Two things of concern: 1) why was the pulley and collar welded? Could there possibly be slop on crank keyway the previous owner have reason to weld? Maybe some other reason? 2) The front of PTO bearing with the locking collar between the basket and bearing should sit flush with the end of the crank. Your picture shows the locking collar sitting almost flush with the end of crank with no room for the bearing. I just hope the crank hasn't been cut/modified in the past. Is there room to push the basket and collar back and allow room for the bearing?
__________________
Two 125's and a 124 all with 42" decks Plow blade #2 Cart QA36 snowthower |
#3
|
|||
|
|||
I don’t know how much room there is supposed to be, but from the back edge of the pulley to the block is about 13/16” to 7/8”. As a Cub neophyte, I don’t know if that space and the design of all those parts would allow the pulley to slide back farther. Not sure how that would change belt alignment with the generator.
I’ll have to check when it’s light and remove the belt to check for any play in the crank. As far as any history, the previous owner and I do not know any detail as to why this was done. |
#4
|
|||
|
|||
Looks like basket became loose on crank and if so both have enough wear that welding them was only recourse without having crank rebuilt and using a good basket. I don't know what that is that's welded to the basket pulley and crank but definitely not a locking collar. Locking collars are female and do not have keyways. More than likely the only way to repair is going to be with a good crank and another basket. Going to be expensive repair. Good luck!
|
#5
|
||||
|
||||
I'm guessing that with some patience and some small cut off wheels, you could get that weld split.
Hard to know why it was done that way. People do really slapdash stuff in the heat of the moment (me included) That said, I've never welded anything to the crank!
__________________
61 and 63 Originals 123 (2) 782D 106, 147, 122 102 parts It's only original ONCE!
|
#6
|
|||
|
|||
Do you have a 4 1/2" grinder? If not buy one. Buy a couple of grinding discs and several thin zip cut blades. It shouldn't take much grinding and cutting in the right places to get that off. You're not trying to save the basket at this point, just the shaft.
|
#7
|
||||
|
||||
I'm going to recommend you remove the engine from the tractor first, makes for better access. Then yeah, a 4 1/2 angle grinder, a few thin disks (3/64" thick), a sharp chisel, a small hammer, and a lot of patience. If I remember correctly the crank shafts are cast iron, so the welds well break off and clean up fairly easily.
Take your time and work at it slowly.
__________________
128 X 2, 129, 149, 1450 x 2 |
|
|
Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.
MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.
This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC
All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.
Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.