Only Cub Cadets

PLEASE PATRONIZE OUR SPONSORS!

CC Specialties R. F. Houtz and Sons Jeff in Pa.

P&K Cub Cadet Machtech Direct

Cub Cadet Parts & Service


If you would like to help maintain this site & enhance it, feel free to donate whatever amount you would like to!




Attention Everyone, we have 2 new Sponsors!
Machtech Direct and P&K Cub Cadet (See Links above)


Go Back   Only Cub Cadets > Cub Cadets > IH Cub Cadet Tractors (GT)

Notices

Reply
 
Thread Tools Display Modes
  #1  
Old 03-01-2011, 09:26 PM
Battlewagon Battlewagon is offline
Member
 
Join Date: Apr 2010
Location: GA
Posts: 84
Default A bit more progress on the K321

Carb mods have started.
The pos subject for drill test. Walbro 52


Hole looks good, now on to the carb that is gonna go on the K321. The Walbro 64
Factory jet.


Holley jet after drill and tap.


Walbro 52 vs Walbro 64(on right)


Walbro 64 (on left) vs Kohler 26


I know David Kirk was able to get a Walbro 52 apart and bored out. I was gonna try this till I got the 64's. But I noticed in my drill test if you go this route you can use Holley jets to get more adjustment. The jet will block the passage of the original needle valve.


A few shots of the M12 Crank

M12 on bottom

M12 on top after machining PTO end for my clutch.








And an inexpensive GM door spring tool that works great for Kohler valve springs.
Reply With Quote
  #2  
Old 03-01-2011, 09:31 PM
_DX3_'s Avatar
_DX3_ _DX3_ is offline
Grand Member
 
Join Date: Jun 2010
Location: Richmond, Kentucky
Posts: 5,798
Default

I used that same door spring tool to remove my valve springs... Works great! Cheap too at the parts store. Or well it was many years ago. LOL
__________________
DWayne

1973: 128, ag tires, 3pt. lift, spring assist, lights, 42" Deck

10" moldboard plow

2016 XT1 42" deck 18HP
Reply With Quote
  #3  
Old 03-01-2011, 10:42 PM
westofb's Avatar
westofb westofb is offline
Senior Member
 
Join Date: Feb 2011
Location: Missouri
Posts: 533
Default They Still Are!

Quote:
Originally Posted by _DX3_ View Post
I used that same door spring tool to remove my valve springs... Works great! Cheap too at the parts store. Or well it was many years ago. LOL
Just seen that tool today at harbor freight, I believe it was about $6.00!
Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 09:34 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.

Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.

MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.

This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC

All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.

Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.