|
PLEASE PATRONIZE OUR SPONSORS!
|
|||||||
 |
|
|
Thread Tools | Display Modes |
|
#11
05-01-2022, 10:55 AM
|
|||
|
|||
The flywheel is behind the little pulley, the grass screen and the blower housing. I have to get the grass screen off first, then the blower housing will come off. Then I’ll have access to the flywheel. How do I get that little pulley and the grass screen off? I have to do that first.
|
|
#12
05-01-2022, 11:13 AM
|
|||
|
|||
|
Have you removed the flywheel nut? You can't take off the pulley or the
grass screen without taking off the nut. Pull the nut and you can move on with your project. Ken
|
|
#13
05-01-2022, 02:30 PM
|
|||
|
|||
|
Got the nut yesterday, I was able to use a three jaw puller on the grass screen. It slipped off before I even got the puller tight. I see that it is indexed with a little steel dowel. Now, what size are the holes to pull the flywheel? Even though I ask many questions, I always check my shop manuals before posting here. A 1/4-20 bolt is too small, and a 5/16-18 seems too big. I have a tap and die set, but I just want to clean threads, not damage the hole. I bought a flywheel puller today.
|
|
#14
05-01-2022, 09:02 PM
|
|||
|
|||
|
I wish I knew what to tell you on the hole size but I don't know. And
nothing apart to check either. trial and error time. If you use the puller much you will end up with a pretty good assortment of bolts. Good Luck Ken
|
|
#15
05-01-2022, 09:11 PM
|
||||
|
||||
|
If 1/4 is too small then the 5/16" is prolly right, but the threads are prolly plugged with many years of debris'
Use your 5/16" tap carefully, and you can clean them up. Might want to first clean with an icepick and air pressure. 
|
|
#16
05-01-2022, 09:40 PM
|
|||
|
|||
|
Thanks for the helping this newbie guys.
|
|
#17
05-05-2022, 03:46 AM
|
||||
|
||||
|
__________________
102 
|
|
#18
05-05-2022, 07:09 AM
|
|||
|
|||
|
Awesome. I have the engine block stripped all the way down. I’m taking it to a machine shop this week.
|
|
#19
05-07-2022, 07:03 PM
|
||||
|
||||
|
Sweet! I would definitely print out the relevant sections of the Kohler rebuild manual and highlight the appropriate dimensions and clearances, at least if the shop doesn’t do a lot of old Kohler stuff. The less guessing and calling you they have to do, the better for all involved.
My $0.02 
__________________
102
|
|
#20
05-08-2022, 09:35 AM
|
|||
|
|||
|
I dropped it off Thursday. He’s been around as long as I can remember and his shop is still at the same location. I asked him if he needed the manual, he said nope I have one. He did say he's going to double check my cylinder bore measurements then call me to advise on a 010, 020 or 030 piston. He also needs me to bring the new valves too for the valve seat work. As I was writing this, I thought of asking him to ensure the top of the block is nice and square too. Thoughts guys?
|
|
|
|
Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.
MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.
This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC
All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.
Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.
Linear Mode
