Only Cub Cadets

PLEASE PATRONIZE OUR SPONSORS!

CC Specialties R. F. Houtz and Sons Jeff in Pa.

P&K Cub Cadet Machtech Direct

Cub Cadet Parts & Service


If you would like to help maintain this site & enhance it, feel free to donate whatever amount you would like to!




Attention Everyone, we have 2 new Sponsors!
Machtech Direct and P&K Cub Cadet (See Links above)


Go Back   Only Cub Cadets > Cub Cadets > CCC/MTD Cub Cadet built Tractors (GT)

Notices

Reply
 
Thread Tools Display Modes
  #11  
Old 08-01-2023, 06:54 AM
3Kseries4ever 3Kseries4ever is offline
Member
 
Join Date: Dec 2019
Location: WI
Posts: 51
Default

I would check the reverse light switch, part of the circuit disengages the PTO when you go in reverse.

Bill
Reply With Quote
  #12  
Old 08-01-2023, 03:10 PM
WALTER's Avatar
WALTER WALTER is offline
Senior Member
 
Join Date: Apr 2009
Location: CORRYTON, TN
Posts: 106
Default 3186

Back up lights work great.
Engine getting hot, I think it caused a vapor lock.
Also have an oil leak. Will have to pull motor to check that out.
Winter project for that.
All the switches work ok.
Any other suggestions.
If worst comes to worst I'll use my HDS 2135.
__________________
Walter
Reply With Quote
  #13  
Old 08-01-2023, 04:01 PM
WALTER's Avatar
WALTER WALTER is offline
Senior Member
 
Join Date: Apr 2009
Location: CORRYTON, TN
Posts: 106
Default 3186

Also low fuel light is working backwards.
__________________
Walter
Reply With Quote
  #14  
Old 08-01-2023, 09:53 PM
Oak's Avatar
Oak Oak is offline
Senior Moderator
 
Join Date: Jun 2009
Location: Georgia
Posts: 5,182
Default

I’m thinking you’re having an issue with the relay.

You need to look at the back of the free service manual and see how the circuit works. You can download it from here.

https://www.mymowerparts.com/pdf/Cub...epair-Manuals/

The B&S models should be the same as the Kohler powered machines. Follow the pto “on” schematic snd see where you are dropping the ground at. Something is probably turning the relay off.

Good luck and let us know.
__________________
This ain't no hobby....it's an addiction
Reply With Quote
  #15  
Old 08-01-2023, 10:43 PM
WALTER's Avatar
WALTER WALTER is offline
Senior Member
 
Join Date: Apr 2009
Location: CORRYTON, TN
Posts: 106
Default 3186

Relay was removed and a jumper wire was put in its place.
Since relay is removed be my problem?
__________________
Walter
Reply With Quote
  #16  
Old 08-02-2023, 06:37 AM
3Kseries4ever 3Kseries4ever is offline
Member
 
Join Date: Dec 2019
Location: WI
Posts: 51
Default

Over heating problems are often plugged cooling fins. If it has been run with the upper baffle off or the accordion connection to the engine off, the engine is literally stuffed with grass fines. Pull all the cooling sheet metal and clean it out. People think those things are not needed and there have been some "rocket scientists" on youtube that say these things can be thrown away - don't believe it.

Bill
Reply With Quote
  #17  
Old 08-02-2023, 08:49 AM
WALTER's Avatar
WALTER WALTER is offline
Senior Member
 
Join Date: Apr 2009
Location: CORRYTON, TN
Posts: 106
Smile 3186

I never throw away the shrouds.
Motor is really dirty, looks like it has 23 years of built up oil, grass and dirt.
More than likely when it cools off I will pull engine from frame and give both a good cleaning and try and see where oil is leaking from.
Getting ready to order front and rear oil seals.
Thanks for advice.
__________________
Walter
Reply With Quote
  #18  
Old 08-03-2023, 05:56 AM
3Kseries4ever 3Kseries4ever is offline
Member
 
Join Date: Dec 2019
Location: WI
Posts: 51
Default

Sounds like a good plan. I have a 3185, which is your tractor but with a Briggs instead of a Kohler engine. Mine currently has 1386 hours on it and lives a pretty luxurious life for a garden tractor. I have a broken back and bad knees and this tractor is my "helper", it gets me around the yard and provides the grunt that I can no longer provide. It was the first of my Cub 3000's and started my addiction. I was never a fan of the sloped nose Cubs, but my disability has changed my view and the step thru design offers me a method of mounting and dismounting in a nearly painless fashion. So enjoy your "new to you" Cub.

Bill

DSC_4081.jpg
Reply With Quote
  #19  
Old 08-03-2023, 09:28 AM
WALTER's Avatar
WALTER WALTER is offline
Senior Member
 
Join Date: Apr 2009
Location: CORRYTON, TN
Posts: 106
Smile 3186

My first Cub was the IH Cub Cadet 582. It had a Briggs and Stratton 16hp. Replaced motor with Kohler 18hp magnum.
Then I got a 682, it had a bad motor. So the magnum came out of 582, and went in the 682. Sold the 582 as it was.
I got a Cub Cadet LT1042. No hump in the middle. The 682 I gave to my nephew, who lives in Iowa, none of our children here wanted it.
Last year I got the HDS2135 with drive shaft to replace the LT1042, the LT1042 kept have stering issues.
A month ago I got the HDS3186. Which I like.
I'm 73 and getting to the point where I'm not as agile as I use to be. So this I hope will last me for a long time.
I'll keep you updated on progress.
__________________
Walter
Reply With Quote
  #20  
Old 08-03-2023, 05:03 PM
Oak's Avatar
Oak Oak is offline
Senior Moderator
 
Join Date: Jun 2009
Location: Georgia
Posts: 5,182
Default

Do you have a good DVOM?

If you do try this

Ignition switch off and pto switch pulled as if you were engaging the mower deck.

Unplug the vacuum solenoid. Use your ohm meter to read continuity from the blue wire of the harness on the machine side to the battery negative terminal. You should read 0 ohms. If you don’t you have an issue with the pto switch, your jumped out relay issue, broken wire or a bad ground wire.

Try that and report back. It sounds like the previous owner made a mess of your wiring.
__________________
This ain't no hobby....it's an addiction
Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 12:44 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.

Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.

MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.

This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC

All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.

Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.