|
PLEASE PATRONIZE OUR SPONSORS!
|
|||||||
 |
|
|
Thread Tools | Display Modes |
|
#11
07-06-2022, 06:31 PM
|
|||
|
|||
The good news is, the flywheel came off this afternoon.
 The bad news is, all the magnets on the back side of the flywheel, became loose, from using that BFH.  Now, does anyone know of a satisfactory adhesive to re-glue these magnets back on ?? 
__________________
[B]Roland Bedell[/B] CC Models: 100, 105, 1450, 782, (2) 784, & 2072 [SIZE="4"][B][COLOR="Red"]Buy:[/COLOR][COLOR="Blue"] Made in the USA[/COLOR][/B] [/SIZE]:American Flag 1: 
|
|
#12
07-06-2022, 06:48 PM
|
||||
|
||||
|
2 part epoxy "steel weld" by Permatex. works for me.
As you prolly know from watching "Terrell fixes all" do keep the north/south orientation in mind as you reattach the "maggots" as well as the spacing. Clothes pins keep the spacing equal and careful clamping of the Maggots so they don't break using vice grips gingerly, while the epoxy dries. clean everything carefully and marking the magnets er "maggots"  avoids any errors in N/S magnetism. in the event the the orientation is not followed, it will not put out max output, if at all.
|
|
#13
07-06-2022, 07:42 PM
|
|||
|
|||
|
Quote:
__________________
[B]Roland Bedell[/B] CC Models: 100, 105, 1450, 782, (2) 784, & 2072 [SIZE="4"][B][COLOR="Red"]Buy:[/COLOR][COLOR="Blue"] Made in the USA[/COLOR][/B] [/SIZE]:American Flag 1:
|
|
#14
07-06-2022, 09:17 PM
|
||||
|
||||
|
Quote:
If you have been lucky, none of the magnets have been destroyed or cracked. I have always had success, regluing them with no problems, using JB Weld and it is not hard to figure out where they go because of markings or rust spots on the inside of the flywheel. But the tricky and most important part is that going around the circle, the magnets must align, end to end, north to south, all the way around. In other words, if you rotate one of the magnets and glue two in with a south pole facing a south pole, and/or a north to north, it may give a charge but not a full charge. Somewhere on the net, there is a diagram or a video explaining this but I don't have it right now. I'll repost if I find it.
|
|
#15
07-07-2022, 01:18 PM
|
||||
|
||||
|
Here ya go Roland....
https://www.google.com/search?q=repl...awbkP7_uauAQ21
|
|
#16
07-07-2022, 01:45 PM
|
|||
|
|||
|
YUP, watched that video.
__________________
[B]Roland Bedell[/B] CC Models: 100, 105, 1450, 782, (2) 784, & 2072 [SIZE="4"][B][COLOR="Red"]Buy:[/COLOR][COLOR="Blue"] Made in the USA[/COLOR][/B] [/SIZE]:American Flag 1:
|
|
#19
07-08-2022, 01:35 PM
|
|||
|
|||
|
While sorting the Magnets for "attracting" or "repelling" one of the magnets is broken. Clean break. Question is, is that magnet toast, or put the break line together, and glue it in?
__________________
[B]Roland Bedell[/B] CC Models: 100, 105, 1450, 782, (2) 784, & 2072 [SIZE="4"][B][COLOR="Red"]Buy:[/COLOR][COLOR="Blue"] Made in the USA[/COLOR][/B] [/SIZE]:American Flag 1:
|
|
#20
07-08-2022, 03:49 PM
|
||||
|
||||
|
Quote:
__________________
Why Farm Half When You Can Farmall? 1282 | 44C Deck, Chains, 42" Blade, Cast Weights, 020" Over K301 * 1711 | 50C Deck, #1 Rear Rototiller w/ Extensions, Sleeve Hitch, KT17S Series II 24302 --> CH18S * 1811 | 46 GT Deck, 42" Blade, Chains, M18 Magnum, Sleeve Hitch * 1782 | 60" #375 Deck, Kubota D640 Diesel * 1862 | #450 Snowblower, M18 Magnum * 782 | Y/W KT17 Series II, Sleeve Hitch * 984 | Y/W Onan/Linamar 20HP, Sims Cab, CAT 0 3 PT w/ Rear PTO, 60" #374 Deck
|
|
|
|
Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.
MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.
This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC
All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.
Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.
Linear Mode
