|
PLEASE PATRONIZE OUR SPONSORS!
|
|||||||
 |
|
|
Thread Tools | Display Modes |
|
#11
07-28-2014, 11:06 PM
|
||||
|
||||
Okay, I'm back. I called around on the oil seals and found that Motion Industries had them in stock but not the ones I posted, those are NLA but they had another brand so I ordered them. I purchased 6 seals for a total of $48 shipped to my door. I pulled all the old seals and cleaned everything up.
DSCN1304.jpg The roller bearings looked okay for not having any grease in them. What was in there was all dried up and nasty so I cleaned them with degreaser and brake cleaner then repacked them with wheel bearing grease after the seals were installed. DSCN1305.jpg The roller bearings are HK 3020 if you ever need to replace them. I pressed one of them out just to see how hard it was and they come out pretty easy. Here is a shot of the new seals installed with the roller bearing block nearest. DSCN1314.jpg Time to button it up. The only place I used Permatex was at the top and bottom of the inner bearing block. I used Ultra Black. DSCN1320.jpg
__________________
This ain't no hobby....it's an addiction |
|
#12
07-28-2014, 11:21 PM
|
||||
|
||||
|
Time to start stacking parts. There are two gaskets, a rear axle cover plate and the differential cover. I used two 1/4-20 bolts and cut the heads off to make reassembly easier.
DSCN1315.jpg Cub Cadet wants $25 for each gasket. I was careful when I removed them and I reused the old ones after I cleaned them up. They can be reused, I have no leaks. They have some type of metal in them so they are pretty tough. DSCN1323.jpg Here is the inside of the rear axle cover plate. The unpainted pieces are some type of spacer plate they use to compensate for the gasket that goes between it and the aluminum rear housing. DSCN1321.jpg That's all the pictures I have. All in all, it wasn't a hard job and so far everything works great.
__________________
This ain't no hobby....it's an addiction |
|
#13
07-29-2014, 07:49 AM
|
||||
|
||||
|
Todd
Outstanding write up on the repair. First time I've seen one of these apart. I'll stick to the older stuff thank you. Can't believe that they didn't design it so that the outer bearings could be greased. This thread will be going in the tech section. 
__________________
2264 with 54 GT deck 1641 AKA Black Jack with a 402-E Haban Sickle bar mower JD317 dump truck BX2670 with FEL |
|
#14
07-29-2014, 12:06 PM
|
||||
|
||||
|
"I don't have a socket big enough but I will next time."
I'm glad I'm not the only one using old pipe and 1/2 " socket wrench to make a breaker bar the few times I need it. Nice work!
__________________
- Tim 1872 60" Haban deck- 2082 450 blower, 50c deck - 1450,1650 2x44a deck, QA-42A snowthrower, 70 w/k181(destroyed) 38" pin on deck |
|
|
|
Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.
MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.
This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC
All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.
Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.
Linear Mode
