|
PLEASE PATRONIZE OUR SPONSORS!
|
|||||||
 |
|
|
Thread Tools | Display Modes |
|
#1
10-18-2014, 11:28 AM
|
||||
|
||||
Steering rebuild and upgrade
I am going to pull the steering column in my 782. The steering has a lot of slop in it. I plan on getting one of the upgrade kits, but do I also need to get a rebuild kit as well? They're $140.00 on the auction site. Didn't know if the rebuild kit was necessary, or if a good cleaning and repack of the lower column would do the job.
Any thoughts? Thanks. 
|
|
#2
10-18-2014, 11:51 AM
|
||||
|
||||
|
Depends on how bad yours is. Take it apart and take a look. It may just need to be cleaned, re lubed and adjusted. They are pretty simple. The service manual will explain how to do them.
__________________
2264 with 54 GT deck 1641 AKA Black Jack with a 402-E Haban Sickle bar mower JD317 dump truck BX2670 with FEL
|
|
#3
10-18-2014, 12:24 PM
|
|||
|
|||
|
The one that was in my cub was the same way, totally roached...when i pulled the plug out of the bottom, all the bearings and remnants of the cages and pieces of metal just fell out..not too mention the housing was cracked.....i am lucky to know where a salvage yard for tractors is, and just took my chances and pulled one...it was Much better shape...i only needed the bottom bearing cage, found it at the farmers implement store....made the foam gaskets, cleaned everything, made my own cam follower out of a grade 8 bolt, re assembled and got a thrust bearing from mcmaster...works great, no slop, one finger steer, and less than 40 bucks....one thing i would recommend is to find a little "whip" for a remote grease zerk, put mine in the frame...i hope this can maybe help you some...if you need a pic of the remote zerk i can get one....good luck
|
|
#4
10-18-2014, 12:37 PM
|
||||
|
||||
|
Here's where I got the parts for the steering upgrade I did on my 1200. The gaskets and bearings I got from cub cadet. I made a new cam follower stud from a grade 8 bolt.http://ihcubcadetparts.net46.net/1_2_Products.html
__________________
Brian April 1979 1200 Quietline 44A deck 1988 1211 customized into a 1288 with a K301AQS 38C deck and a 1864 54” deck . Snow blades 42" and 54" . Brinly disk, brinly plow a cultivator and a $5 brinly yard rake! 
|
|
#5
10-20-2014, 04:22 PM
|
||||
|
||||
|
I rebuilt the steering unit on my 1811 and what I found out was that the shaft with the worm gear is the heart of the whole thing. If it is worn or rough and pitted then the kit will not do any good. That's what I found on mine and that is why I decided to go with power steering. Mine was worn to the point, even though it was still smooth, that the guide bolt would bottom out before the sides of the gear would make good contact with it. BTW, after you install the kit it will feel great on the bench. The real test is when you put it back into the CC and you can expect to have to re-adjust the bolt a little. When I figured how much it was going to cost for a new(used) steering column I decided then that PS would only be a few hundred more. The 1811 has the two turn model and is highly desirable therefore it cost a lot more for the shaft. Good luck
__________________
1811 Hydro "Failing to prepare is preparing to fail".
|
|
|
|
Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.
MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.
This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC
All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.
Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.
Linear Mode
