|
PLEASE PATRONIZE OUR SPONSORS!
|
|||||||
 |
|
|
Thread Tools | Display Modes |
|
#1
08-30-2024, 05:33 PM
|
|||
|
|||
125 Hydro Issue
Why would my hydro work at low rpms, but when I have the engine speed up for mowing it doesn't want to move? Last week when I was mowing I was having a similar problem, if not the same, so I took the relief valves out to make sure they weren't half open, and they're fine and seem to be working properly. The filter doesn't even have 100hrs on it.
|
|
#2
08-30-2024, 07:27 PM
|
||||
|
||||
|
How is the fluid level? 100 hours, how many years since both the fluid and filter have been changed? What are you running for oil and filter make and number?
__________________
2264 with 54 GT deck 1641 AKA Black Jack with a 402-E Haban Sickle bar mower JD317 dump truck BX2670 with FEL
|
|
#5
08-31-2024, 02:26 AM
|
|||
|
|||
|
Quote:
__________________
'65 100 w/ creeper, '68 125, '75 1000, '76 1250 w/ hydraulic lift and 3pt, '77 "2550", '78 1200 w/ rear pto and spring assist lift, '79 1250, several mowing decks, 42" snow blower, 42" dozer blade, Brinly plow, 5' Massey disk, and New Idea dump cart
|
|
#6
08-31-2024, 02:29 AM
|
|||
|
|||
|
Quote:
__________________
'65 100 w/ creeper, '68 125, '75 1000, '76 1250 w/ hydraulic lift and 3pt, '77 "2550", '78 1200 w/ rear pto and spring assist lift, '79 1250, several mowing decks, 42" snow blower, 42" dozer blade, Brinly plow, 5' Massey disk, and New Idea dump cart
|
|
#7
08-31-2024, 02:32 AM
|
|||
|
|||
|
Quote:
__________________
'65 100 w/ creeper, '68 125, '75 1000, '76 1250 w/ hydraulic lift and 3pt, '77 "2550", '78 1200 w/ rear pto and spring assist lift, '79 1250, several mowing decks, 42" snow blower, 42" dozer blade, Brinly plow, 5' Massey disk, and New Idea dump cart
|
|
#9
08-31-2024, 08:46 AM
|
|||
|
|||
|
I would change the filter and then cut and inspect the old one for any signs of parts or materials that don't belong.It sounds like you have done the most common parts to fail. Good luck,I also have and enjoy my 125
|
|
#10
08-31-2024, 09:01 AM
|
|||
|
|||
|
The spirol pins (what should be installed there, and not split roll pins) may look good and still be visible on either or even both sides of the coupler but still be broken internally, with one or both ends you may be able to see still stuck in the coupler.
I suggest you hold the coupler tight w/pliers and and try to spin the driveshaft while doing so with another pair of pliers or vise grips. I have seen this issue before an 882 diesel which are hard on pins. Both ends still in the coupler but the hydro input shaft not turning. And when driving the old pin out, what's left of it comes out in pieces. It may be tough lining up the coupler with the hole in the driveshaft when installing a new spirol pin, use a short length of 1/4" bolt shank to line the holes up and drive the new pin in while pushing the piece of bolt out the other side. Good luck! NOTE TO SELF: replace the pins in the 882 BEFORE heading to Bluneirs plow day in October!!
|
|
|
|
Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.
MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.
This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC
All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.
Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.
Linear Mode
