|
PLEASE PATRONIZE OUR SPONSORS!
|
|||||||
 |
|
|
Thread Tools | Display Modes |
|
#1
10-28-2012, 08:00 PM
|
||||
|
||||
Parts by Jeff-sleeve hitch, PTO buttons and custom parts
I make a large variety of parts for Cub Cadets. I can make custom parts too. All parts are made by myself, I'm a machinist / fabricator with over thirty years experience.
Please contact me by: PM or E-mail at: JRDerstine@gmail.com ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ ~~~~~~~~~~ Heavy duty sleeve hitch adapter with two drilled lifting straps or two slotted lifting straps  $110 plus shipping $125 plus shipping with one set of drilled and one set of slotted straps Add a Lift Pin for an additional $10 triple drilled lift pin for an additional $15 Extended length to clear tiller mount add $5 I can make these custom length if needed. ~~~~~~~ Lift Pin for rear lift casting, double hole. I drill these so they can be positioned with the holes vertical or horizontal. They are secured with a 3/16" cotter pin and also have a cotter pin where it goes thru the casting.  $17 plus shipping triple drilled long length available too ~~~~~~~~~ Height adjuster Knob for 1/1A/2A tillers using 1/2-13 threaded rod. Has correct milled radius on bottom to match rear lift pin.   $18 plus shipping ~~~~~~~~~~~ 1/2-13NC threaded rod for use with above knob ( or factory knob )  $6 plus shipping ~~~~~~~~~ Brass PTO button  $5.50 each plus shipping ~~~~~~~ Pair of "frankenstein" bolt and nuts for WF rear lifts  $30 plus shipping ~~~~~~~~~ Pair of straps for the front of the QA mounts. No more fumbling with bolts,nuts and washers. Slide these in the hole and secure with a 1/2-13NC in the factory welded nut inside the frame.  $12 plus shipping ~~~~~~~~~~~ Solid Motor Mounts for QL & WF tractors, with washers, Grade 8 flanged bolts and nylock nuts. $40 plus shipping for set of four.  ~~~~~~~~~~~ Headlight rings for 1X2/1X3/1X4/1X5  $32 per pair plus shipping ~~~~~~~~~~~ See later posts for original lift pin and QA36 / QA42 / QA36A / QA42A belt tensioner adjustment parts ~~~~~~~~~~~~~ If you order more than one item, I will do my best to keep shipping costs as low as possible. All parts manufactured by me and mailed from the Palm,PA post office Please either PM or email me Thanks Jeff |
|
#2
03-29-2013, 09:10 PM
|
||||
|
||||
|
90° Gear Box Shafts for tillers and snow throwers. Made from 3/4" diameter 4140 P alloy steel ( turned ,ground and polished ) with on size keyways and snap ring grooves cut.
 $48 each or $92 for the pair plus shipping If you have a "BB" angle drive gear box, I can make those shafts if you send me the shaft to copy ( it will be returned if wanted ) Just found out there are two different lengths of the short shaft in the 90* gear box. One ( as pictured above ) at 4-21/64" long and the other at 4-1/8" long. Just let me know which one you want.  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Two more different lengths. Top on is 5-15/16" long and the bottom is 4-9/64" long  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Transfer shaft for the QA snow throwers. $32 plus shipping or $30 with either ( or both ) of the above 90* gear box shafts  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ PTO pulley puller The pulley puller uses the 5/16" threaded holes in the pulley to pull it off much easier. Each unit is supplied with handle and threaded rod with centering point to locate on the crankshaft. Use a 9/16" wrench or socket.  It's used as shown here ( version shown in pictures does not have the weld cutouts, all pullers have that now)  $22 each plus shipping ~~~~~~~~~~~~~ Ross steering box adjustment screw (Cam Follower)  $8 plus shipping |
|
#3
01-07-2014, 03:53 PM
|
||||
|
||||
|
Adjustable length Lift Bar for front mounted implements. Adjust range of just under 28" to over 32" ( can make custom length if needed )
$35 plus shipping   ~~~~~~~~~~~~~~~~ NF Lift Bracket for front mounted blade $30 plus shipping  ~~~~~~~~~~~~~~~~ Lift Bracket for either hydraulic lift or electric lift. This is the cut down version of the manual style. $17 for the drilled , $20 for the slotted plus shipping  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Receiver Hitch for the 82 series tractors. It bolts to the upright frame in the back.   $50 plus shipping |
|
#4
01-19-2014, 12:41 PM
|
||||
|
||||
|
~~~~~~~~~~~
Original style Lift Pin  $22 plus shipping ~~~~~~~~~~~~~ Tensioner Bolt for QA36 / QA 42 / QA36A / QA42A belt with castle nut & plate button . This style has a welded nut in the end for use with 3/4" wrench. ( original style will offered later after I bend up handles) These are 1/2 -13 LEFT HAND thread    I'll also sell just the bolt and castle nut too Complete unit as shown $30 plus shipping Adjustment bolt with castle nut $17 plus shipping Plate button $17 plus shipping |
|
#5
02-23-2014, 07:12 PM
|
||||
|
||||
|
Attachment Brackets for lift handle, both NF & WF.
 $22 plus shipping ~~~~~~~~  Wide Frame rear lift attachment bracket also $22 plus shipping ~~~~~~~~~~~~~~~~~~~~~~~ 
|
|
#6
03-23-2014, 10:12 PM
|
||||
|
||||
|
Driveshafts now being offered
Made from 4140 alloy steel Prices are $45 plus shipping for welded flange style  and $30 plus shipping for drilled only. ~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Driveshaft Couplers for 5/8" driveshaft to creeper gearbox or manual transmission.  $25 plus shipping ( if purchased with a driveshaft, $20 ) ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Drive Hubs - $45 plus shipping. One piece design for added strength 
|
|
#7
08-03-2014, 08:20 PM
|
||||
|
||||
|
Rear Lift Pin - Triple drilled pin for rear lift casting. I drill these so they can be positioned with the holes vertical or horizontal. They are secured with a 3/16" cotter pin and also have a cotter pin where it goes thru the casting.
 $22 plus shipping ( $17 with sleeve hitch adapter order ) |
|
#8
10-01-2014, 09:12 PM
|
||||
|
||||
|
Transfer Shaft for the QA snow throwers. $32 plus shipping or $30 with either ( or both ) of the 90* gear box shafts
|
|
#9
08-24-2015, 07:21 PM
|
||||
|
||||
Thank you again Jeff in PA. Highly recommend asking Jeff to make some odd ball stuff that you may need as he just sent me a wide frame creeper handle and steer axle pin and bushings for my 108 project. Top knotch quality, fitment, etc. thanks Jeff
image.jpg
__________________
(2) Original, 100, 102, 124, 73, 800, #1 and #2 cart, brinly plows, disk, IH184, IH244, 1948 F Cub |
|
#10
09-07-2015, 07:20 PM
|
||||
|
||||
|
Creeper handle - $35 plus shipping
WF shown -- Will make narrow frame long ( tall tunnel )as shown for same price. If you want short tunnel handle with extension, $43 plus shipping for both. $10 for just the extension   ~~~~~~~~~~~~~~~~~~~~~~ Creeper Poppet Indent Lever - $15 each plus shipping  ~~~~~~~~~~~~~~~~~~~~~~ Brake Pivots for NF manual trans Large pin, small pin & hex head adjustment bolt $25 plus shipping  ~~~~~~~~~~~~~~~~~~~~~~~~~ Axle Pins for NF & WF - $15 plus shipping 
|
|
|
|
Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.
MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.
This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC
All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.
Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.
Linear Mode
