|
PLEASE PATRONIZE OUR SPONSORS!
|
|||||||
 |
|
|
Thread Tools | Display Modes |
|
#1
06-09-2012, 10:07 AM
|
|||
|
|||
Toolbox/Bumper
I would like to add/fab a toolbox and bumper to my 1450. If anyone has bolted a toolbox onto thier tractor, could you post pics or explain where you mounted it? I am thinking a smaller metal type for a few hand tools, small chain, clevis, pins, ect. I was thinking somewhere behind the seat between the tailights, if I could bolt it in there without drilling holes into the seat pan. Maybe running up some braces off of bolts in the rear end area? Same with a front bumper. I can build one, just not sure how and where on the front to attatach it so it won't interfere with other attatchments.
thanks 
|
|
#2
06-09-2012, 10:12 AM
|
||||
|
||||
|
Xtreme motor works makes a tool box that fits behind the tailights and is fairly reasonable. If you wanted a bumper with a tool box i would take an old mule drive and make it from there. Provided you have enough steel laying around to make it the way you want. Hope this helps!
__________________
1967 IH Cub Cadet 123 1978 IH Cub Cadet 1650 19?? IH Cub Cadet 682
|
|
#4
06-10-2012, 12:32 PM
|
||||
|
||||
|
This is what i did its a bumper/toolbox/weight bracket uses the quick hitch system up front.
__________________
Original,100,123,129,1200,1250,168 in progress (3) 42inch plows, QA-42A,#1 tiller, 10inch brinly plow, Case Ingersoll 224, 1948 Farmall H, 1950 McCormick W-6, 1952 McCormick W-4.
|
|
#5
06-10-2012, 12:38 PM
|
||||
|
||||
|
how about some pics of thoses fenders.
__________________
Donovan: 62' Original-fenders 63' 100R-K-321a,lights,creeper,electric lift 149-original paint, tiller, three point, duals, ags 1811Custom -M18-18hp kohler magnum, power steering and hydraulic lift with Three point and sleeve hitch. ---------------------------------------------------- Attachments:three-QA 42inch,42inch blade,one-38inch cast end, QA 44inch deck Brinly 12inch plow, 2x cultivators and x2disc Brinly Tool bar cub10: 
|
|
#6
06-10-2012, 01:32 PM
|
||||
|
||||
|
Tool Box
I was thinking of putting two pieces of "U" shaped channel under the seat bolts that extend rearward that would hold small tools that I need while using the tractor. Things like pliers, hammer, wrench and an oil squirt can. I believe the two pieces of steel would easily support such items and would not interfere with the rear lift. I was also thinking of adding a front bumper to the deck mule that would use the big side bolts and be either bolted or welded to the mule its self. I already have two large nuts welded into my front frame for the Johnny bucket I bought and could use them as well. The problem I have run into with that plan is that the two big side bolts are not long enough to accommodate two pieces of steel in the same space.
__________________
1811 Hydro "Failing to prepare is preparing to fail". 
|
|
#7
06-10-2012, 06:56 PM
|
||||
|
||||
|
Quote:
__________________
Allen Proud owner of my Original and 126! My Grandpa's Cart Craftsman Lawn Sweeper Craftsman Plug Aerator
|
|
#8
06-10-2012, 10:02 PM
|
|||
|
|||
|
Thanks for the ideas on the tool box and bumper. No I did not get the cart. I saw that it was gone and a few days later my neighbor stopped by and said that there were two trailers over there I could have and told me where he left them. One is a craftsman, and one was a larger dumpcart. I don't know the Mfg. of it. I will get some pics of them. I was surprised that he kept the #2 as it needed a lot of work.
|
|
|
|
Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.
MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.
This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC
All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.
Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.
Linear Mode
