Only Cub Cadets

PLEASE PATRONIZE OUR SPONSORS!

CC Specialties R. F. Houtz and Sons Jeff in Pa.

P&K Cub Cadet Machtech Direct

Cub Cadet Parts & Service


If you would like to help maintain this site & enhance it, feel free to donate whatever amount you would like to!




Attention Everyone, we have 2 new Sponsors!
Machtech Direct and P&K Cub Cadet (See Links above)


Go Back   Only Cub Cadets > Cub Cadets > Cub Cadet Engines > Briggs & Stratton Engines
Reload this Page 18HP Vanguard replacement for a KT17 issues.
Register FAQ Calendar

Notices

Reply
Page 1 of 3 1 23
 
Thread Tools Display Modes
  #1  
Old 12-26-2021, 05:35 PM
Johnd Johnd is offline
New Member
  
Join Date: Nov 2017
Location: Ontario
Posts: 20
Default 18HP Vanguard replacement for a KT17 issues.
Quote:
Originally Posted by CubDieselFan View Post
Here you go.

https://www.smallenginewarehouse.com...t-682-Category

Expensive, yep. Better than buying a new mower.
Got engine, thanks! A Vanguard 18hp, a so called drop in replacement for the original Kohler KT17.

There's a couple glitches so far.

1. The distance from the PTO pulley to the crankshaft back face is 3/4" too short. I need a solution for that. Stretching the driveshaft is not an option.

2. The new engine spacers supplied to the old PTO back plate are too thick to be able to bolt the PTO assembly on to the crank with the new bolt. I used the original thinner spacers and removed one of the new brass spacers (of the three supplied) that goes on the shaft behind the PTO. There's no room for the new crank bolt lock washer either.
Reply With Quote
  #2  
Old 12-28-2021, 09:16 AM
Sam Mac's Avatar
Sam Mac Sam Mac is offline
Administrator
  
Join Date: Feb 2010
Location: Galax VA
Posts: 18,813
Default
I suggest that you contact the supplier.
__________________
2264 with 54 GT deck
1641 AKA Black Jack with a 402-E Haban Sickle bar mower
JD317 dump truck
BX2670 with FEL
Reply With Quote
  #3  
Old 12-28-2021, 10:13 AM
Farmall450's Avatar
Farmall450 Farmall450 is offline
Grand Member
  
Join Date: Oct 2018
Location: Marengo, Illinois
Posts: 1,102
Default
Quote:
Originally Posted by Sam Mac View Post
I suggest that you contact the supplier.
Ditto -- ask them what's going on, send a few pictures or better yet call them. If it's a direct fit that shouldn't be going on?

Also, it's very easy to modify the driveshaft length.
__________________
Why Farm Half When You Can Farmall?
1282 | 44C Deck, Chains, 42" Blade, Cast Weights, 020" Over K301 * 1711 | 50C Deck, #1 Rear Rototiller w/ Extensions, Sleeve Hitch, KT17S Series II 24302 --> CH18S * 1811 | 46 GT Deck, 42" Blade, Chains, M18 Magnum, Sleeve Hitch * 1782 | 60" #375 Deck, Kubota D640 Diesel * 1862 | #450 Snowblower, M18 Magnum * 782 | Y/W KT17 Series II, Sleeve Hitch * 984 | Y/W Onan/Linamar 20HP, Sims Cab, CAT 0 3 PT w/ Rear PTO, 60" #374 Deck
Reply With Quote
  #4  
Old 12-28-2021, 10:13 AM
Johnd Johnd is offline
New Member
  
Join Date: Nov 2017
Location: Ontario
Posts: 20
Default
Quote:
Originally Posted by Sam Mac View Post
I suggest that you contact the supplier.
The supplier (Small Engine Warehouse) emails;

"John, I attached the adapter drawing "it looks like bolts are 1/4 by 20 thread" you might try to find some 3/4" spacers or washers. I don't have any spec for the clutch you might try the tractor dealer for this info. Thank you"

So I ordered some 1/4" x 1-1/4" thick fender washers and longer bolts from Amazon to fill the 3/4" gap from the engine to the driveshaft flex connector. I found in my supply of nuts and bolts, a longer bolt to attach the PTO clutch.
Reply With Quote
  #5  
Old 12-29-2021, 09:46 AM
Sam Mac's Avatar
Sam Mac Sam Mac is offline
Administrator
  
Join Date: Feb 2010
Location: Galax VA
Posts: 18,813
Default
Post some pics so we can see what your issue is.
__________________
2264 with 54 GT deck
1641 AKA Black Jack with a 402-E Haban Sickle bar mower
JD317 dump truck
BX2670 with FEL
Reply With Quote
  #6  
Old 01-01-2022, 04:59 PM
Oak's Avatar
Oak Oak is offline
Senior Moderator
  
Join Date: Jun 2009
Location: Georgia
Posts: 5,176
Default
I would move the engine so that the pto is in the proper location and just make a new driveshaft. I made one using a crappy drill press and it works fine. Just find a good piece of shaft like this stuff and you should be good to go for less than $35 or give Jeff a shout and he can make you one.


https://www.onlinemetals.com/en/buy/...nish/pid/15486
__________________
This ain't no hobby....it's an addiction
Reply With Quote
  #7  
Old 01-01-2022, 05:22 PM
ol'George's Avatar
ol'George ol'George is online now
Grand Member
  
Join Date: Oct 2009
Location: MI
Posts: 6,692
Default
Tractor supply has 5/8 shafting in the welding area with the angle iron usually.
Reply With Quote
  #8  
Old 01-01-2022, 05:29 PM
Farmall450's Avatar
Farmall450 Farmall450 is offline
Grand Member
  
Join Date: Oct 2018
Location: Marengo, Illinois
Posts: 1,102
Default
Quote:
Originally Posted by Oak View Post
I would move the engine so that the pto is in the proper location and just make a new driveshaft. I made one using a crappy drill press and it works fine. Just find a good piece of shaft like this stuff and you should be good to go for less than $35 or give Jeff a shout and he can make you one.


https://www.onlinemetals.com/en/buy/...nish/pid/15486
I'd just slice the old one and sleeve it with some pipe of slightly smaller ID than the original shaft's OD. Plug weld and you're golden.
__________________
Why Farm Half When You Can Farmall?
1282 | 44C Deck, Chains, 42" Blade, Cast Weights, 020" Over K301 * 1711 | 50C Deck, #1 Rear Rototiller w/ Extensions, Sleeve Hitch, KT17S Series II 24302 --> CH18S * 1811 | 46 GT Deck, 42" Blade, Chains, M18 Magnum, Sleeve Hitch * 1782 | 60" #375 Deck, Kubota D640 Diesel * 1862 | #450 Snowblower, M18 Magnum * 782 | Y/W KT17 Series II, Sleeve Hitch * 984 | Y/W Onan/Linamar 20HP, Sims Cab, CAT 0 3 PT w/ Rear PTO, 60" #374 Deck
Reply With Quote
  #9  
Old 01-01-2022, 08:40 PM
ol'George's Avatar
ol'George ol'George is online now
Grand Member
  
Join Date: Oct 2009
Location: MI
Posts: 6,692
Default
Tractor supply has 5/8" rod that makes a nice driveshaft.
I have made 4 using it with no problems.
It will vibrate if it does not run true, then you will be replacing couplings as well as rag joints.
Your tractor do as you like, good luck.
Reply With Quote
  #10  
Old 01-15-2022, 02:54 PM
Johnd Johnd is offline
New Member
  
Join Date: Nov 2017
Location: Ontario
Posts: 20
Default
I made the 3/4" drive extension with fender washers. This then made the Vanguard 18hp engine the same length as the Kohler KT17s rebuilt engine that was in the 682.

20220104_125245 resized.jpg

Next, I attached the Haban snowblower and went to install the pulley belt. Well, guess what. The engine PTO pulley was now 3/4" forward of the Haban pulley. WTF!

So, I took off my 3/4" fender washer extension, and of course the pulleys aligned perfectly. It's weird that the Vanguard 18hp fit better than the rebuilt KT17s.

20220105_125740 resized.jpg

More pictures;
20220105_140909 resized.jpg

20220105_125807 resized.jpg

I drilled a hole through the heat shield above the muffler for better throttle cable alignment, and added a rubber grommet there.

20220105_125850 (2).jpg

Since there has been no snow to blow yet, where I live, I cannot say how well the new engine performs yet. I've only taken it up and down the driveway so far. Starting the engine produced blue smoke the first few times, but that appears to be settling out.

Now I have to get rid of the old rebuilt Kohler engine.
__________________
IH Cub Cadet 682
Haban snowblower attachment
Reply With Quote
Reply
Page 1 of 3 1 23

« Previous Thread | Next Thread »

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -4. The time now is 01:25 PM.

www.onlycubcadets.net - Archive - Top

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.

Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.

MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.

This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC

All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.

Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.