|
PLEASE PATRONIZE OUR SPONSORS!
|
|||||||
 |
|
|
Thread Tools | Display Modes |
|
#1
03-02-2021, 08:47 AM
|
||||
|
||||
Ideas for a rusty tank
I've got a couple of gas tanks, all of which have varying degrees of surface rust inside.
Any (good) ideas to deal with it? I've heard of putting some small metal objects (nuts, etc) inside and agitating to clean the rust off, but then what? Hard to get a tank to last 60 years these days without showing signs of wear 
__________________
61 and 63 Originals 123 (2) 782D 106, 147, 122 102 parts It's only original ONCE!
|
|
#2
03-02-2021, 09:17 AM
|
|||
|
|||
|
There are baffles inside the tank that will not allow abrasives items to get to that area.
Best to research chemical de-rusting solutions such as muratic acid. Just be sure to follow label directions as well as precautions. Worked for me on my tanks. Did several at a time so I could reuse the solution.
|
|
#3
03-02-2021, 09:58 AM
|
||||
|
||||
|
I'm going to ASSUME you are working on small engines not a motor vehicle tank.
If so, they have no Baffles, so throw in a handful of rocks, nuts or what have you and shake the shit out of it. It helps if you put some vinegar in them a day or two earlier. as it loosens/dissolves some of the light rust. Depending what you have for contamination, other products might prove better if you have say varnish or similar. Do take out any screen that might be in the outlet and put in a plug so the liquid will stay inside during the agitation process. When finished, wash out with soap/ water and dry in the sun. Rust in a tank that doesn't flake off, poses no problem, as it hurts nothing. 
|
|
#4
03-02-2021, 10:23 AM
|
||||
|
||||
|
Thank you gentlemen.
Yes, sorry this is in a couple of Kohler tanks that I'm going to do, so baffle-less. I ordered some tank coat elixir and will use that after some mech/chem rust removal. Darned alcohol/water in gas these days ...grrhhhh. I appreciate the advice!
__________________
61 and 63 Originals 123 (2) 782D 106, 147, 122 102 parts It's only original ONCE!
|
|
#5
03-02-2021, 10:45 AM
|
|||
|
|||
|
I have had pretty good luck using straight vinegar or maybe some Acetone.
Let it sit for a couple days shaking it up whenever I think about it. Lots of soap and water after that. Ken
|
|
#6
03-02-2021, 10:49 AM
|
||||
|
||||
|
Look up Evapo-rust. I never used it on a gas tank, but I have used it on other things and it works good. It is non toxic, and reusable. I was planning on using it on the tank for my 149, but then I found a nice rust free one.
__________________
125, 126, 147, 129, 149 x 2, 1450, 882, 1810, 1320, 1440, 2135, 2 129’s for parts/project, 1950 Farmall Cub 38" LT mower deck, 4 42" triangle mower decks, 2 44A mower decks, 2 50C mower decks, 42” GT deck, 3 42" snow/dirt blades, 42" landscape rake, #4 cart      
|
|
#7
03-02-2021, 02:37 PM
|
||||
|
||||
|
Do as you like, I have no respect for a "cream" of sorts in a tank.
Maybe because I'm the one that is handed a mess that someone did a while back and it went all bad and am asked to "fixit up" because it rusted between the "coating" and tank or the coating is rattling around inside loose, like a pocket full of marbles. No offence, just my experience. Or like JB weld to stop a leak around a fitting. Just fix it right by sweat soldering the hole or bung in the first place. Luck!
|
|
#8
03-02-2021, 02:48 PM
|
|||
|
|||
|
What size tanks are we talking about here?
I can assure you that the larger ones DO have baffles in them Take a pen light and look, towards BOTH ends. Hell, you can even feel them if your fiddle finger is long enough. I just checked several on my shelf that I cleaned last year and they ALL have them. That's one of the first things I look for, rust in the tank. Every Cub tank I have ever looked into has them.
|
|
#10
03-02-2021, 04:35 PM
|
||||
|
||||
|
Quote:
Hi George, I'm not trying to "fixit up", but to do it right. I plan to remove as much of the rust as I can mechanically/chemically/electrically , but given that I live in North Carolina, if I am successful at removing the rust that's there without some sort of coating immediately following it's going to rust again right away. I *could * get by "fixit up" by just letting it continue to rust and depend on sediment filters and screens to get rid of the continual rust, but I hoped to do better than that, not to take the slack route. You're saying I shouldn't worry about rust in the tank after I knock the big chunks off mechanically? This is a tank for a 123/K301 John
__________________
61 and 63 Originals 123 (2) 782D 106, 147, 122 102 parts It's only original ONCE!
|
|
|
|
Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.
MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.
This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC
All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.
Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.
Linear Mode
