PLEASE PATRONIZE OUR SPONSORS!
|
|
Thread Tools | Display Modes |
#1
|
||||
|
||||
Sleeve hitch ripper
I built this ripper to use next year when I have to level out my yard after my new septic system that was installed this summer. I'll likely have to add some weight to it to get it in the ground. It should make for lots of seat time next year. It is 35" wide and the tines are 7" tall.
__________________
Adam 1964 Model 100 w/ K301 12hp and custom hydraulics 1972 Model 149 turned 129 w/ K301 12hp, triple hydraulics, 66 series clone |
#2
|
||||
|
||||
nice work looks heavy duty
__________________
982D kwik-way loader w/3 spool control and front and rear remotes,2182, 1812 cat 0, 1440 puller, 3185 grass killer, 2x 450s, QA42, 364, tiller |
#3
|
|||
|
|||
Looks awesome!
__________________
Mark 1971 Model 73 - Hydraulic lift,Fenders,Creeper,Lights,Sleeve hitch and Weights 1967 Model 102- mower 1965 model 70 - weights,rear lift and spring assist Model 100 resto mod project, rear PTO, hydraulic lift QA42 snow thrower 42in front blade Grandpa's F-12 and Super M |
#4
|
||||
|
||||
Very nice Adam
I think I want one no, I really want one, that would be handy for a couple different things.
__________________
Make the best of each day , Todd Original's Face Lift thread.http://www.onlycubcadets.net/forum/s...ad.php?t=34439 (O) Start to Finish video.https://www.youtube.com/watch?v=GAoUNNiLwKs Wheel Around videohttps://www.youtube.com/watch?v=XUL-m6Bramk They can't all be turn key! |
#5
|
||||
|
||||
Nice work IHinIN
|
#6
|
||||
|
||||
__________________
Adam 1964 Model 100 w/ K301 12hp and custom hydraulics 1972 Model 149 turned 129 w/ K301 12hp, triple hydraulics, 66 series clone |
#7
|
||||
|
||||
Looks good
( the sleeve hitch adapter is upside down though ) |
#8
|
|||
|
|||
It looks really good Adam! I hope it works for you though. I just recently tried to set up a cultivator I have in the configuration of a chisel plow...... I about tore the Brinly adapter up. One side would plow in deep while the other side didn't want to. The plow would "walk" side to side because it was being pulled from the center. If it had been a 3pt configuration it would not have been a problem because it would have had a wider and more even pull from the spread on the 3pt arms. If one corner of the ripper snags a root, or a rock, or even just a hard patch it will want to twist the hitch. My experience: I took it off before it tore up my hitch. I actually bent it a little.
Good luck! |
#9
|
|||
|
|||
Nice job!! Are you going to sharpen the front edge of the tooth?
|
#10
|
|||
|
|||
Looks great Adam, nice work.
The sleeve doesn't go "above" the sleeve hitch adapter frame? Prolly wouldn't bend one of these.
__________________
More IH Cub Cadet Parts RIGHT HERE |
|
|
Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.
MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.
This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC
All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.
Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.