Only Cub Cadets

PLEASE PATRONIZE OUR SPONSORS!

CC Specialties R. F. Houtz and Sons Jeff in Pa.

P&K Cub Cadet Machtech Direct

Cub Cadet Parts & Service


If you would like to help maintain this site & enhance it, feel free to donate whatever amount you would like to!




Attention Everyone, we have 2 new Sponsors!
Machtech Direct and P&K Cub Cadet (See Links above)


Go Back   Only Cub Cadets > Cub Cadets > Customized Cub Cadets
Reload this Page Chain Drive??
Register FAQ Calendar

Notices

Reply
Page 1 of 2 1 2
 
Thread Tools Display Modes
  #1  
Old 07-02-2010, 11:50 PM
DieselOnly DieselOnly is offline
New Member
  
Join Date: Jul 2010
Location: Illinois
Posts: 10
Default Chain Drive??
I've got my Cub Cadet Original in pieces. Have plenty of stripper on hand and the electrolysis tank is ready to go.

The only gripe I ever had with this little tractor was that sometimes the drive belt (between the engine & the drive shaft) would slip. I was considering replacing the two pulleys with sprockets and running a drive chain rather than the belt. Now I know that I am, in essence, moving the designed (and perhaps intentional) "weak" point of the system to some other component (maybe the drive-shaft itself?). Anyone ever done (or seen) this? Maybe up-sizing the cross sectional area of the drive-shaft would provide the increase in moment to equal the new load and less energy loss.(?)
Reply With Quote
  #2  
Old 07-03-2010, 03:26 AM
Methos Methos is offline
Banned
  
Join Date: Feb 2010
Location: NC
Posts: 10,941
Default
Reply With Quote
  #3  
Old 07-03-2010, 06:59 AM
camarokidz28's Avatar
camarokidz28 camarokidz28 is offline
Senior Member
  
Join Date: Mar 2009
Location: MI
Posts: 532
Default
__________________
Denny
Original Member # 389
Saw It
Wanted It
Had A Fit
Got It

MY Cubs Original x 2 , 70 x 7 , 71 x 2 , 72 x 4 , 73 , 76 , 100 x 3 , 104 , 106 , 109 , 128 , 129, 147 x 2 , 804 , 2 Wheel Horses and Lorenzo's 2 - 804's
Reply With Quote
  #4  
Old 07-03-2010, 07:55 AM
MBounds's Avatar
MBounds MBounds is offline
Member
  
Join Date: Mar 2009
Location: Joaquin, Texas
Posts: 459
Default
DieselOnly: Welcome to the OCC...If the Original drive belt has been slipping, it's because of improper tensioning. Follow the adjustment instructions in the manuals and you won't have that problem. That belt, in good condition (not old and dry-rotted) and when properly adjusted, will allow that Original to move even a turning plow through the soil with nary a slip....That's from experience.... You dont really need to re-invent the driveline....BTW: ALL manuals are available from a sponsor.
__________________
Myron B
East Texas
Most of of the fleet:

Cub Cadets: 2 Orig,70,71,122,123,104,124,126,86,128, 109,800,1200,1250,1450,1650,IH 682,782D,IH 982. Cadets: 76,SO76,80,81,IH 182. RER: 60,75. Elec 95. Trailers: #2, #3, #4, 1200-A,1200-B,1200-C, 2000. IH 1210 P/U, an IH Scout II and an IH Scout 800 to tow 'em with.
Reply With Quote
  #5  
Old 07-03-2010, 08:31 AM
gcbailey's Avatar
gcbailey gcbailey is offline
Grand Member
  
Join Date: Jul 2009
Location: WV
Posts: 1,430
Default
when I first got my 'O' it was slipping horrible going uphill with just me. It wouldn't even pull out in 2nd. I had over 1.5" of slack. After reading the adjustment in the manual and using a 3' piece of angle iron to help give me the tension, it works great now. You can adjust the tension by yourself, but it's best for a 2 person job. One to push with the rod and the other to tighten the bolts back.
__________________
Gary
'49 Farmall Cub, '62 "Original, '70 73 w/402-D Haban sickle, '71 127 w/38" cast end deck, '73 149, '76 Sof76, '07 LT1045 w/bagger, '09 GT2544 w/bunch of mods.

5 Exmarks, Kubota B2920, blah, blah, blah...
Reply With Quote
  #6  
Old 07-03-2010, 09:52 AM
Yosemite Sam Yosemite Sam is offline
Grand Member
  
Join Date: Mar 2009
Location: Medora, IL
Posts: 3,866
Default
DieselOnly,

If you are really into design, engineering, fab work and modifying things, then go ahead and give it a try (didn't mean for that to sound like I'm trying to be a smart "butt").

Otherwise, when you put your Original back together, if you use the correct belt and tighten it properly, you shouldn't have any problems with it.

None of my Originals ever slip their belts.
Reply With Quote
  #7  
Old 07-04-2010, 04:24 PM
dross dross is offline
New Member
  
Join Date: May 2009
Location: IL
Posts: 24
Default belts
That belt adjusted properly will pull hard enough to kill a 7 horse.
Reply With Quote
  #8  
Old 07-05-2010, 12:07 AM
DieselOnly DieselOnly is offline
New Member
  
Join Date: Jul 2010
Location: Illinois
Posts: 10
Default
Alright, alright. I've never been married, but I know how to listen. I will admit to a proclivity to "tinker" and "improve".

Upon further inspection (per suggestions in this tread) I found that indeed that old belt was not only looser than goose poop, but VERY dry (bits crumbled off with a slight touch. NOT ONLY that, but!...the portion of the belt that contacts the pulleys exhibited much signs of slippage (probably for a long time) in the appearance of a "glazing"!

So, gentleman of jury, I will (for now) fore-go my intended upgrade and defer to the manuals for proper instruction on belt tensioning when this thing goes back together.


And, for now, I guess, I'll let that Wisconsin THD continue to sit on its little cart...and not try to shoe-horn it into the the Original.

I'll try things the right way once before I try them "my" way.
Reply With Quote
  #9  
Old 07-23-2010, 05:31 AM
hillbilly hillbilly is offline
Member
  
Join Date: Jul 2010
Location: IN
Posts: 67
Default
If you should happen to change engines for a larger kohler, you can run a double 50 roller chain down to a drive shaft and install a cub lowboy three finger clutch back at the transmission. My dad had also built a twin belt clutch for the origionals. These were all in pulling tractors with 48ci motors turning 7000 rpm.
Reply With Quote
  #10  
Old 07-23-2010, 09:50 AM
Methos Methos is offline
Banned
  
Join Date: Feb 2010
Location: NC
Posts: 10,941
Default
Reply With Quote
Reply
Page 1 of 2 1 2

« Previous Thread | Next Thread »

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -4. The time now is 01:50 AM.

www.onlycubcadets.net - Archive - Top

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.

Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.

MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.

This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC

All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.

Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.