PLEASE PATRONIZE OUR SPONSORS!
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
4 Axle Disc
I didn't actually make everything of course, but I did hand build the frame and 3-point hookup for it. I used the disc axles and blades from two Brinley discs.
|
#2
|
||||
|
||||
Looks great! More pics!!!
__________________
Terry O,100,72,102,123,104,124,105 125,129,149,1200,982 (2)2182s w/60in Habans 3225 |
#3
|
|||
|
|||
Looks good, but the front gangs need to meet in the center and the gap should be wide in the center of the rear gangs. If not, it won't fill the dead furrows or work correctly. Sorry to be the "bad news guy" but it's not set up correctly.
|
#4
|
|||
|
|||
Well I haven't tried it yet, the ground is too wet...
I had to use two different size gangs, the rear is from a bigger disc than the front. One of the reasons I posted it was to get feedback on the setup. I've never used a disc. I'll hopefully get a chance to try it out when I get home from work. |
#5
|
|||
|
|||
The rear should have one more blade per gang than the front and the outermost blade about half the diameter. But, equal blades front and back will work. Think about it like this: each blade in front makes a furrow, then each blade on the rear reverses the direction the dirt is rolled and fills in the furrow.
The angle of the "V" also isn't steep enough. The problem with the these small disk blades is they dish a little too much for no larger than they are. To do a good job the smallest usable blade is 12". I believe the Briny disks are 9". |
#6
|
||||
|
||||
Rotated for easier viewing
__________________
-Ryan
|
#7
|
||||
|
||||
Just my bu to me it looks like if he moved the front gangs in a bit and moved the rear gangs out a bit it would work a little better. Granted these smaller GT discs aren't the greatest in the world but they do a fine job when set up right.
__________________
-Ryan
|
#8
|
|||
|
|||
The front blades are 10 1/2" and the back ones are 11 1/2".
The angle is set up exactly as the frame they came off of. I've been looking for a set of gangs to match the rear, but no luck so far. Thanks for the comments. I'll move the rear gangs out as mush as I can. |
#9
|
|||
|
|||
I understand that the angle is probably the same as what it was originally, but that's my point. Brinly didn't build them with enough angle, which is part of the reason that they don't cut well. Since you went to the effort to build the disk, it's worth it to get it set up correctly.
Edit: Sorry, I don't mean for that to sound harsh, just trying to help. |
|
|
Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.
MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.
This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC
All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.
Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.