![]() |
PLEASE PATRONIZE OUR SPONSORS!
|
|||||||
![]() |
|
|
Thread Tools | Display Modes |
|
#1
|
||||
|
||||
![]() The side where the arrow is sticks out the front more than the other side...Is this normal, how it was made or am I missing something? I know the center is bent and I straightened that after this was taken, but none of the welds are broken! Had me perplexed.
__________________
"We don’t stop playing because we grow old, we grow old because we stop playing."
|
|
#2
|
||||
|
||||
|
Its probably not square, check the corners with a square and you'll probably find its bent in a diamond shape.
__________________
Tim Pap's 100 Restored 108 1211 Dual Stick 1050 Pap's 100 restoration thread - http://onlycubcadets.net/forum/showthread.php?t=47965 |
|
#3
|
|||
|
|||
|
Agree. That could show up when you latch it in the quick attach.
|
|
#4
|
||||
|
||||
|
Let me clarify...The U shape piece in the photo isn't what I am talking about. it is the bottom part on the right in the photo. The point of that is sticking out further on that side than the other. I have gone over this thing and there are no welds broken that would allow that to move like it is. I am beginning to think that is the way it was originally welded up. All the shafts line up fine...I was just puzzled as to why it may be out like that on one side
__________________
"We don’t stop playing because we grow old, we grow old because we stop playing."
|
|
#5
|
||||
|
||||
|
It's kind of obvious that at some point in it's life it ran into something and got tweaked a bit. A BFH and a vise and a couple love taps and you should be able to straighten it out. I just straightened one out this past summer that was in way worse shape the that.
__________________
1641, 1541, 682 with 18hp command engine and hydraulics from a 782. 1872 with a power angle blade. |
|
#6
|
||||
|
||||
|
If it attaches to the tractor easily I wouldn't worry about it, if it hard to attach then its bent.
__________________
Tim Pap's 100 Restored 108 1211 Dual Stick 1050 Pap's 100 restoration thread - http://onlycubcadets.net/forum/showthread.php?t=47965 |
|
#7
|
||||
|
||||
|
I see what you talking about, where the U shaped part is welded to the one side of the quick attach part. It could simply have been bent a little funny at the factory and had to stick out a little farther to be welded square, I wouldent worry about it as long as it locking in on both sides when you mount it.
__________________
149 with kwik-way loader,1772,two 1782 super smokers, 982 SGT w 54" haban blade,60" haban deck, 50in deck cat 0 3 point, brinly cat 0: blade, plow(3), disc.123,hydro lift. 61"O" Brinly single row planter,brinly cultivator,#2 trailer,brinly 10 inch plow,3 42 inch blades,Model #1 Tiller with extenstions,haban sickle mo. 106w/ags and hydro lift.
|
|
#8
|
||||
|
||||
|
Quote:
If it ain't broke don't fix it!!!!
__________________
"We don’t stop playing because we grow old, we grow old because we stop playing."
|
|
#9
|
||||
|
||||
|
Hammer time...
__________________
Tractor #1--1972 Model 149 with rear lift Tractor #2--1972 Model 149 with rear lift 1A tiller w/both extensions, 38" & 42" Mower Decks, Wheel Weights, Ohio Steel Fabricators 10" mold board plow, two 42" snow blades, QA-42A Snow Thrower, Brinly Sleeve Hitch |
|
#10
|
|||
|
|||
|
I just worked on a mule that is straight and has that same overhang. On the same side. So I would consider that lip normal in the construction of the mule. Appears they left a little material instead of making an additional cut to the angle.
|
![]() |
|
|
Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.
MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.
This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC
All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.
Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.