|
PLEASE PATRONIZE OUR SPONSORS!
|
|||||||
 |
|
|
Thread Tools | Display Modes |
|
#1
10-14-2011, 09:44 AM
|
||||
|
||||
882 Driveline alignment problem
Okay diesel owners, I got a question. I received my new parts for the driveline replacement on my 882 and there is something not correct with mine. The original engine to ragjoint flange has 3 bolts that bolt to the crankshaft. The ragjoint uses 4 bolts and this causes one of the bolt heads to be back to back and not have proper clearence. The red and blue lines added to the first pic are how the ragjoint bolts line up. The blue line is how the shaft coupler lines up and the bolt at the 10 oclock position is where the problem is.
The next four pics are the problem bolt at 12-3-6-9 oclock postions. There seems to be an angular alignment problem with the engine to hydro input shaft. At 12 oclock there is a gap, 3 & 9 not much if any and it hits at 6. I remember Matt G had the same problems with his diesels and I wanted to see what yours is doing. I would like to correct this problem but may not be able to if it is an angular and or elevation problem. Thanks.
__________________
This ain't no hobby....it's an addiction 
|
|
#2
10-14-2011, 09:55 AM
|
||||
|
||||
|
I will go out and look at mine in a bit, but what about shimming the disks out a bit further at these two spots?
__________________
DWayne 1973: 128, ag tires, 3pt. lift, spring assist, lights, 42" Deck 10" moldboard plow 2016 XT1 42" deck 18HP
|
|
#4
10-14-2011, 10:05 AM
|
||||
|
||||
|
Well mine looks just like yours, bolt head to bolt head. I don't have a very good shot, but can see very little difference in them.
__________________
DWayne 1973: 128, ag tires, 3pt. lift, spring assist, lights, 42" Deck 10" moldboard plow 2016 XT1 42" deck 18HP
|
|
#5
10-14-2011, 10:18 AM
|
||||
|
||||
|
I'm thinking this is a design flaw. I don't think it would have been a problem if they used a four bolt drive cup. Is the one bolt head worn on yours also?
__________________
This ain't no hobby....it's an addiction
|
|
#6
10-14-2011, 02:31 PM
|
||||
|
||||
|
It's a design flaw. Mine did that too so I took the one bolt to a grinder and shaved off of the bolt head a little so they would just barely touch and not actually hit each other that hard. I think Matt mentioned shaving one down also. Poor design.
__________________
Adrian 2072 (789513)
|
|
#8
10-14-2011, 03:44 PM
|
||||
|
||||
|
Quote:
BTW, they couldn't use a 4-bolt drive cup without changing the pulley on the engine...they likely used what the engine came with, and everybody overlooked the contact between the bolt heads.
|
|
#10
10-14-2011, 05:52 PM
|
|||
|
|||
|
Quote:
 I learned from Allen you don't know if you don't ask. 
|
|
|
|
Cub Cadet is a premium line of outdoor power equipment, established in 1961 as part of International Harvester. During the 1960s, IH initiated an entirely new line of lawn and garden equipment aimed at the owners rural homes with large yards and private gardens. There were a wide variety of Cub Cadet branded and after-market attachments available; including mowers, blades, snow blowers, front loaders, plows, carts, etc. Cub Cadet advertising at that time harped on their thorough testing by "boys - acknowledged by many as the world's worst destructive force!". Cub Cadets became known for their dependability and rugged construction.
MTD Products, Inc. of Cleveland, Ohio purchased the Cub Cadet brand from International Harvester in 1981. Cub Cadet was held as a wholly owned subsidiary for many years following this acquisition, which allowed them to operate independently. Recently, MTD has taken a more aggressive role and integrated Cub Cadet into its other lines of power equipment.
This website and forum are not affiliated with or sponsored by MTD Products Inc, which owns the CUB CADET trademarks. It is not an official MTD Products Inc, website, and MTD Products Inc, is not responsible for any of its content. The official MTD Products Inc, website can be found at: http://www.mtdproducts.com. The information and opinions expressed on this website are the responsibility of the website's owner and/or it's members, and do not represent the opinions of MTD Products Inc. IH, INTERNATIONAL HARVESTER are registered trademark of CNH America LLC
All material, images, and graphics from this site are the property of www.onlycubcadets.net. Any unauthorized use, reproductions, or duplications are prohibited unless solely expressed in writing.
Cub Cadet, Cub, Cadet, IH, MTD, Parts, Tractors, Tractor, International Harvester, Lawn, Garden, Lawn Mower, Kohler, garden tractor equipment, lawn garden tractors, antique garden tractors, garden tractor, PTO, parts, online, Original, 70, 71, 72, 73, 76, SO76, 80, 81, 86, 100, 102, 104, 105, 106, 107, 108,109, 122, 123, 124, 125, 126, 127, 128, 129, 147, 149, 169, 182, 282, 382, 482, 580, 582, 582 Special, 680, 682, 782, 782D, 784, 800, 805, 882, 982, 984, 986, 1000, 1015, 1100, 1105, 1110, 1200, 1250, 1282, 1450, 1512, 1604, 1605, 1606, 1610, 1615, 1620, 1650, 1710, 1711, 1712, 1806, 1810, 1811, 1812, 1912, 1914.
Linear Mode
